Determining Correct Length Replacement Leaf Spring

Question

Question:

when I measure the old spring 25.5 and I see the one you all have is 25 1/4 what should I due. Also my trailer sets very close to the trailer tire can I increac the height I have the right tire size

asked by: Bryan

0

Expert Reply:

Trailer leaf springs can grow longer after many years of use. A new springs that measures 25-1/4-inches long like # e57SR could easily measure 25-1/2-inches after years in service on a trailer. Springs can lengthen as much as 3/4 of an inch. If your old spring measured 25-1/2 you can safely conclude that it is actually a 25-1/4-inch.

Our main leaf spring page is linked for you. Just click on your dimension and axle weight rating to see suitable options.

Generally you want no less than 3-inches of space between the tire's top tread surface and the trailer frame. Odds are that your new springs (always replace all springs at the same time) will lift the trailer slightly thanks to them being stiffer than the old ones.

expert reply by: Adam R

0

Matthew

3/13/2024

I am rebuilding a heavy utility trailer. The trailer was home build. Rust has taking hard at its springs and I would like to replace them. The springs are eye to eye with a length of 41 inches. They are a 1 an 3/4 wide with 8 leafs. I have not been able to find anything online even close.. The trailer is double wheeled with a single axle and walking beams. 5 X 10. Any help would be appreciated. Thanks

Jon G.

3/13/2024

@Matthew There aren't any standard leaf springs that match your 41" eye-to-eye measurement so you're looking at either cutting off and welding new hangers for a shorter set of leaf springs, or going with an alternative suspension type altogether. If you let me know the weight rating of your trailer axles I can make some alternative recommendations for you.

Matthew

3/13/2024

@JonG Thanks for you quick response. Like I said trailer is home built heavy duty. The main axle is 2 1/8 stainless steel. I would guess they harvested the springs from a car or small truck. I have no problem welding new springs on. The trailer pulls up to 2 tons. I will need springs and new hangers, pins etc. If you could give me a recommendation on something close. Thanks again

Jon G.

3/14/2024

@Matthew It's a pretty common thing to take vehicle parts and use them for homemade trailers so you aren't alone. To replace your hangers and leaf springs I recommend the following kits: - Single-Axle Trailer Hanger Kit # APS4 (which will give you 5" or 5-1/2" clearance between trailer frame and axle) - 25-1/4" Long 4-Leaf Double-Eye Spring for 5,000-lb Trailer Axles # e44SR Since you said the trailer pulls up to 2 tons I went with the 5K spring just to make sure we cover the weight of the trailer as well as your loads. For this setup you'll have the hangers spaced out 24-7/8" on center with the bolt holes for the leaf spring.

Helpful Links

tv-review-etrailer-trailer-leaf-spring-suspension-e47sr.aspx

Answer 1

Hey Eric, if you were wanting a scissor jack style of leveling jack the part #JSC-24 would be a great set. Is the type of jack you were wanting or were you thinking something more like a stabilizer jack like the Trailer Valet #TV68FR.

view full answer...

Answer 2

Hey, Lance. The direction the springs are in doesn't matter. They can be to the front or to the rear of the axle and will perform the same either way. What kind of trailer are you working on?

view full answer...

Answer 3

Your axle has dimensions that we don't have any direct leaf spring style axles for but we do have a Timbren axle less kit like the part #ASR3500S05 which is a 3,500 lb axle solution. This is similar to a torsion setup but uses a rubber spring and…

view full answer...

Answer 4

Hello Mike, Thank you so much for the detailed information, most helpful! For the leaf springs, you will want to go with (6) of the 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR. Since you have 7K axles, these are the…

view full answer...

Answer 5

Hey Ben, so yes you can and for that rated spring in the same length you'd want the part #DX23CR.

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 7

Hello Damon, thanks for reaching out. It looks like both the fwd and awd models of the 2015 Acadia can be flat towed. I will start with a parts list followed by a few notes about towing your Acadia. - Demco Classic Base Plate Kit - Fixed Arms…

view full answer...

Answer 8

To determine the location for the front and rear hangers on your tandem axle trailer you will first need to make sure that you have the correct center point for your equalizer hanger. The center point of your equalizer hanger needs to be located…

view full answer...

Answer 9

We have found that the Seaflo Diaphragm water pumps like the part #SE57FR are very quiet compared to other options but especially compared to the Shurflo pump you have. This is also a 3 gallon per minute pump rated for 55 PSI.

view full answer...

Answer 10

Hey Dennis, thanks for reaching out! The 4-Leaf Double-Eye Spring #DX23CR has a 3" drop from center eye to middle of the leaf spring (see attached photo). For a single axle setup I recommend the Hanger Kit #APS4, and for a tandem axle setup I…

view full answer...

Answer 11

Hi Austin, I can help you determine the right replacement double-eye leaf springs for your 2018 Jayco trailer, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as all you need to do is measure your…

view full answer...

Answer 12

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...