Will Bulldog Swivel Jack Pipe Mounts # BD015279 and # BD005024 Work Together

Question

Question:

I wanted to verify that Item # BD015279 and Item # BD005024 are compatible and work together.

asked by: Joel

0

Expert Reply:

Yes, Bulldog pipe mounts # BD015279 and # BD005024 are compatible with each other. I have included links to videos on both parts for you.

expert reply by: Michael H

0

Answer 1

The item you selected, Bulldog Jack, Sidewind Swivel - 2,000 lbs, part #BD1541150301, requires the use of a pipe mount to be welded to the frame of your trailer. I contacted our representative at Bulldog, and he informed me that to mount part…

view full answer...

Answer 2

Assuming that your shackle links measure 2-1/4 inches center hole to center hole, the ideal replacement for your existing #A2252CB-GALV suspension equalizers would be the #K71-653-00 E-Z Flex kit from Dexter Axle which is good for axle capacities up…

view full answer...

Answer 3

Good question. You are correct that the #A2252CB-GALV is 2-7/8" tall. When measuring an equalizer we will always go from center hole to center hole. The best way to measure the height is to first draw a line between the two lowermost holes, then…

view full answer...

Answer 4

Thanks for the pictures! Based on the weight of your 2008 Keystone Cougar 5th Wheel, you will want the item #LG-1 landing gear set. You are going to want to measure to be sure this is the right size for you. The two things you will want to measure…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C15400 and the Curt Trailer Hitch Receiver part #C15800 are the exact same trailer hitch save for one has a 2" receiver tube opening and the other a 2-1/2" receiver tube opening. The dimensional drawing…

view full answer...

Answer 6

According to my research, the correct replacement rotor for your Dexter 12K Axle (Non-ABS) is the Replacement Rotor for Dexter Disc Brakes part #070-006-01 which measures 11" in diameter. The Dexter 10K and 12K axles will both use the same…

view full answer...

Answer 7

I do have an option for you but we don't offer any direct bolt-on swap options for the Tie Down Engineering LP7000 Actuator due to the age. That said, we do have plenty of great replacement options like the Dexter DX7.5L A-60 Brake Actuator part…

view full answer...

Answer 8

The Bulldog Jack part #BD190754 that you referenced would get welded on for installation. It can be welded on in various positions and setup, but I attached a picture of what a similar jack would look like welded on.

view full answer...

Answer 9

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 10

I went out to the warehouse and pulled the Optronics Replacement Side Marker Lens #AL9RB. It measures 2-13/16 inches across, 2-1/8 inches tall, and it is 3/16 of an inch thick. The mounting holes are 2-5/16 inches apart on center. The lens is for…

view full answer...

Answer 11

Hey Seth, yes we do have a hub/drum that fits the etrailer 7k axle part #e95GR with a 6 on 5-1/2 inch bolt pattern with the part #AKHD-655-6-EZ-K.

view full answer...

Answer 12

The difference in tire diameter will be an additional 2-1/2 inches going from the 225/75-15 which measure 28.4 to the 235/80-16 which measure 30.9 inches. As a general rule of thumb the minimum safe distance between front and rear tires on the same…

view full answer...

Will Bulldog Swivel Jack Pipe Mounts # BD015279 and # BD005024 Work Together

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching