Stake Pocket Tie-Down Anchor T55Z Dimensions

Question

Question:

I am interested in your Stake Pocket Tie-Down Anchor for Flatbed Truck or Trailer - Zinc - 2inch D-ring - 1,600 lbs p/n- T55Z. My stakes measures exactly 3-1/2 x 1-1/2. Are the dimensions on your website the actual outside dimension, or are they undersized to fit a 3-1/2 x 1-1/2 opening?

asked by: Gary T

0

Expert Reply:

The actual outside dimensions of the stake pocket anchors part # T55Z that you referenced where it slides into the stake pocket is the exact dimensions you listed. 3-1/2 inch by 1-1/2 inch. I attached a picture that has these dimensions listed.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Dan! I see you were looking at the Hellwig anti-sway bars so if you want to stick with Hellwig you can use the Rear Anti-Sway Bar - 1-1/2" Diameter #HE78RR. If you're experiencing a lot of sway I recommend adding the Front Anti-Sway Bar…

view full answer...

Answer 8

You will naturally see some voltage drop from the brake controller all the way back to your trailer brakes, but what you're describing sounds like a bad ground somewhere. What you need to do is check the grounds related to the trailer brakes and…

view full answer...

Answer 9

Hello Todd, thanks for reaching out. I do have an option for you, but a direct replacement for the TDE LP70 actuator is not available. Our best option for replacing it is the Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes #099-175-20. This is a…

view full answer...

Answer 10

Hey Jeff! The Dexter 12V KTI Hydraulic Pump #DX53ER does not include oil. The most common recommendation is probably Dexron III. This is what KTI officially says for their pumps: "KTI recommends using a premium hydraulic oil to ensure optimum…

view full answer...

Answer 11

Hey Dale, both DeeMax and Hydrastar make really nice disc brake components. Either kit is going to work really well for your 2022 Grand Design Reflection 337RLS. If you want the best of the best and don't mind paying for the premium brand then go…

view full answer...

Stake Pocket Tie-Down Anchor T55Z Dimensions

Product Page this Question was Asked From

Continue Researching