Replacement Bolts for the Thule Adventurer Cargo Box

Question

Question:

Is it possible to just order the bolts from this hardware kit I only need four, and what is the part number?

asked by: John S

0

Expert Reply:

You would need 4 Carriage Bolt M6-1 x 75mm - Fully Threaded, part # TH10403.

These are the replacement bolts that come in the Thule QM3 Quick On-Off Mounting Hardware Kit for Adventurer Cargo Box, part # TH04997.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hello Lou, thanks for reaching out. The hitch pin you are looking for is the etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories #e43JR. This will work with the Benton #B54VR bike rack you mentioned, as well as the #B54FR,…

view full answer...

Answer 3

Hello Andrew, Well that sounds like quite the fun trip, what state or states will you be traveling through? You're asking a really important question, especially since you're planning a cross-country trip with about 250 pounds of bikes and…

view full answer...

Answer 4

Hello Karla, Wow, that is a really nice e-bike! I do not blame you for wanting a ramp for your e-bike, just because you can lift your bike doesn't mean that you should. For your 2024 Aventon A-Level 2 step through Commuter E-bike I recommend the…

view full answer...

Answer 5

Hi Stephanie! Great question and you’re totally right to ask, because most hitches for the 2024 RAV4 do require a bit of bumper trimming. That includes the Oris Detachable Hitch #TS66VR, since it uses a hidden design that needs a hole cut in the…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hello Joseph, yes there is! What you are looking for is the Anti-Rattle Hitch Lock and Cable Lock for 2" Hitch Mounted Bike Racks #e88RV. This will work with the Benton Bike Rack #B54VR, as well as the #B94FR and #B54FR so that the bike and rack…

view full answer...

Answer 8

Great question, Hannah. Both use wheel-mount systems and avoid frame contact, but the Crosstrack 1 bike 2" hitch #HLY98RR has a tilt feature and no-tool install thanks to the No-Wobble feature (uses a handle that you twist by hand). The Kuat…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hey Mike! The Benton Shifts&Grins Bike Rack for 4 Bikes item #B82FR does not have any built in locks which is a big part of why it comes at such an affordable cost compared to other manufacturer's offerings. You can easily secure your bikes…

view full answer...

Answer 11

The Hollywood Racks Trail Rider 2-Bike Rack #HR200 weighs about 35 lbs. The Swagman XC 2-Bike Rack #S64650 is lighter at about 26 lbs. The biggest difference between the two is the Swagman rack is rated for 2 bikes at 35 lbs each and the Hollywood…

view full answer...

Answer 12

Hi Cameron! For your 2025 Mazda 3 Sedan, I prefer the Curt #C44DR over the Draw-Tite #24982. They are almost identical and have the same weight capacities, but Curt is made in America and Draw-Tite is not. This pretty much always pushed me to the…

view full answer...

Replacement Bolts for the Thule Adventurer Cargo Box

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching