Installing The 7 Pin Wiring Adapter For 2006 Ford F-150

Question

Question:

HI.I HAVE AN 06 F150.4X4 EXT. CAB. I HAVE JUST INSTALLED A NEW 7 PIN CONNECTOR ONTO TRUCK OLD ONE DAMAGED.THIS ONLY HAS THE 4 LIGHT WIRES AND OTHER THREE JUST HAVE TAPED-OFF PIGTAILS.IS IT THE 118247 THE PART I NEED?I JUST INSTALLED A CURT/VENTURA ? BRAKE CONTRIOLLER.IM GUESSING YOU DONT HAVE THE HARNESS WITHOUT FEMALE 7 PIN CONNECTOR.OK IF NOT,IS JUST NEW.IS MY THINKING CORRECT,THAT FACTORY WIRING ACQUIRED TRUCK WITH RECEIVER AND 74 WIREPIN END GOES BACK TO FRAME RAIL CONNECTOR,DROPS TO A 4WIRE IF TRUCK IS NOT ORDERED WITH FACTORY TOW PACKAGE?SORRY FOR ALL THIS INFO/QUESTIONS BUT THANK YOU TOO.

asked by: TODD R

0

Expert Reply:

On your 2006 Ford F-150, there should be an OEM connector that can clip right in. The Tow Package Vehicle Wiring Harness with 7-Way Trailer Connector # 118247 is the 7 way adapter you are looking for. I've attached a help article to assist in the installation and have attached a video.

expert reply by: Jason S

0

Answer 1

The brake controller installation on your 2006 F150 is pretty easy. The connector for the brake controller is located under the dash, behind and to the right of the OBD port as shown in the video I've linked for you. You'll need the brake…

view full answer...

Answer 2

Hi Dave; since you just wired the Tekonsha BRAKE-EVN Trailer Brake Controller #TK28BR I would double checking the wiring since that is likely the cause of the power interruption error. Make sure your red wire is secure and only getting power when the…

view full answer...

Answer 3

To install a brake controller in your 2008 Ford F-150 you would be able to use the brake controller port under the dash and you will need to complete the wiring at the rear of your vehicle to the 7-way at the rear of the truck. For a brake controller…

view full answer...

Answer 4

2004 was a split model year for the Ford F150. Two F150 models were offered, the Heritage which was the rounded body style like the 2003 model or the new body style, like the 2005 model. The hitch you need will depend on which body style your truck…

view full answer...

Answer 5

I have a great solution for you. In order to replace your factory hitch on your 2005 Ford F-150, you need to purchase and install an aftermarket bumper. This is because the OEM hitch on a 2005 Ford F-150 tie into the factory bumper while our…

view full answer...

Answer 6

Hey Chas, so we do have a similar solution to what you are looking for that provides a 7-way for your 2003 Ford F-150 with the Curt part #C55242. This would definitely work for you and is currently available.

view full answer...

Answer 7

Hello Brian; I'm not sure what connector you have on there or what you're looking at. However, the Tow Package Vehicle Wiring Harness with 7-Way Trailer Connector #118247 is confirmed to fit the 2004 Ford F-150 that has a factory 4-way. If…

view full answer...

Answer 8

The Ford Replacement OEM Tow Package Wiring Harness part #118243 is indeed a fit for a 2000 Ford F-250. It will replace the 7-way trailer connector as well as part of the trailer wiring harness from the square pigtail onward. I would not have any…

view full answer...

Answer 9

You really should not have to put a plastic bag over the trailer connector on your vehicle during rain. It should be protected enough that that would not be necessary. In fact, the plastic bag could actually have collected water and held it to the…

view full answer...

Answer 10

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Installing The 7 Pin Wiring Adapter For 2006 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching