Lumens Output of Strip Light ILL71CBAWN

Question

Question:

Code: ILL71CBAWN how many lumens emitted please? Do you carry any interior strip lighting in black rather than chrome?

asked by: Tani B

0

Expert Reply:

The Lumens rating for the # ILL71CBAWN is 342 Lumens. The part # ILL70CBSBAWN is a similar light with a black base.

expert reply by: Jameson C

0

Answer 1

Because an LED lamp like the #ILL71CBAWN draws very little power (about a 1/3 of an amp), using a small gauge wire like the 16 gauge #16-1-1 which is sold by the foot would work fine for the lamps you mentioned. I've linked to an install video…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Lumens Output of Strip Light ILL71CBAWN

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching