What Is The Wall Thickness Of The Curt Solid Steel 1-1/4" Hitch Bar with Raw Finish - 24" Long?

Question

Question:

What is the wall thickness?

asked by: Don

0

Expert Reply:

I reached out to my contact at Curt to make sure I give you the most accurate measurement. The wall thickness on the Curt Solid Steel 1-1/4" Hitch Bar with Raw Finish - 24" Long, # C49524, is 0.221 inches.

expert reply by: Jason S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 7

Hey Donna, yes the Replacement Grease Cap for Dexter/Tie Down Engineering Vortex Trailer Hubs #DE69NR that you referenced does work as a replacement for your Dexter 21-261 cap. How do you like the Vortex trailer hubs?

view full answer...

Answer 8

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 9

Hi John! The BulletProof Aluminum Hitch w/ Stainless Steel Dual Ball for 2" Hitch - 4" Drop/Rise - 14K #BPH32YR is anodized, so it isn't just raw aluminum. That actually goes for all of BulletProof's aluminum ball mounts, which is…

view full answer...

Answer 10

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Answer 11

Welcome back Gary. To replace a 2" coupler that fits a 2" wide trailer tongue our options are limited to the Channel Tongue Trailer Coupler item #CT-3001-Z. It's got the standard trigger latch. There's not many options for couplers…

view full answer...

Answer 12

Hey Jason! I'm guessing you have the 12" long shank right now which is the standard. For a longer shank that fits a 2-1/2" receiver you can use the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 16" Long - 7" Rise,…

view full answer...

What Is The Wall Thickness Of The Curt Solid Steel 1-1/4" Hitch Bar with Raw Finish - 24" Long?

Product Page this Question was Asked From

Continue Researching