The Buyers Products # 3371809042 measures 9-1/2" on the vertical side with the remaining height being 6" down to the bottom. The # 3371809043 measures 14-1/2" on the vertical side with 8" of remaining height down to the bottom of the hitch plate. See the dimensional diagrams below. view full answer...
The distance between the bolt holes from side-to-side on the Buyers Products Hitch Plate with Receiver Tube # 3371809067 are 35.05 inches apart. The height of the mounting flange is 6-1/2 inches. The distance between the bottom of the flange to the crossbar is about 8-3/4 inches. I went ahead and attached photos of the spec sheets available from Buyer's Products.
If you are wanting a more adjustable hitch option, I recommend the Adjustable Width Trailer Hitch Receiver for RVs, 22" to... view full answer...
Since you have a C4500 the correct Buyers Products Hitch Plate with Pintle Mount would actually be the part # 3371809039A as the # 3371809065 is for the 3500 model trucks. view full answer...
While the Buyers Products Fabricators Hitch Plate # 3371809027A does not carry a weight rating, their custom fit hitch plates are only rated for 20,000lbs. Since this is a fabrication kit you will be able to add more steel and additional mounting points to increase the hitch strength and be able to bolt on the Buyers Products 30 Ton Pintle Hook # 337PH30. I recommend having the plate fabricated and strengthened at a shop experienced in this work. view full answer...
In regards to the Tow Ready Combo Bar with 2" Trailer Hitch Receiver part # 80948, the longer the receiver tube is less support you'll have. That said, we cannot provide specifics on this as there are several other variables at play so in order to obtain a true rating you'll need to consult an engineer.
Please note, the Roadmaster Hitch Mounted Spare Tire Carrier part # RM-195225 reduces hitch capacity by 1/3 . view full answer...
The best option we have for your 2001 International 4700 is going to be a weld-on hitch plate. Unfortunately there are no bolt on options available for your truck. Make sure to use an experienced welder for installation of the hitch plate. We have the following hitch plates available:
Buyers Products Fabricators Hitch Plate - 5/8" x 34-1/2" x 22-1/2" # 3371809043
Buyers Products Fabricators Hitch Plate - 1/2" x 34-5/8" x 15-5/8" # 3371809040
Buyers Products Fabricators Hitch Plate... view full answer...
The only hitch that is capable of handling 25,000 lbs for your 2016 Ford F-550 Cab and Chassis is the TorkLift SuperHitch Magnum Trailer Hitch Receiver # TLF1003-30. This hitch has a 2-1/2" and 2" receiver with a maximum gross trailer weight of 20,000 lbs and maximum tongue weight of 2,500 lbs.
In order to be able to tow 25,000 lbs, you would need to use the TorkLift SuperHitch Everest Weight Distribution System # TLWD1000 which would increase the gross trailer weight to 30,000 lbs... view full answer...
I recommend one of the Buyers Products Fabricators Hitch Plate Kits for your 2006 GMC Topkick 7500 as there is not a hitch plate specific to your vehicle. Here are the ones we carry.
Buyers Products Fabricators Hitch Plate - 3/4" x 34-1/2" x 22-1/2" # 3371809027A
Buyers Products Fabricators Hitch Plate - 5/8" x 34-1/2" x 22-1/2" # 3371809043
Buyers Products Fabricators Hitch Plate - 1/2" x 34-5/8" x 15-5/8" # 3371809040
Buyers Products Fabricators Hitch Plate - 5/8" x 34-1/2" x 15-1/2"... view full answer...
The Buyers Products Plain Receiver Tube # 337RT255818 and Reese Combo Bar # 11029 are both 18" and the longest 2-1/2" receiver tubes that we offer. view full answer...
Yes it will; according to the manufacturer, Buyers Products, your Ford F-450 cab and chassis will allow you to mount, without drilling, the Buyers Products hitch plate bumper, which is the following part number:
- Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 view full answer...
The best trailer hitch option we'll have for an International 4700 Series Truck is the Buyers Products Fabricators Hitch Plate part # 3371809027A. This is a hitch plate that will be used for custom fabrication. It can then be outfitted with a receiver tube, pintle hook, etc.
I have attached some other plate size options for you in a list below. view full answer...
Yes we do; I have added a photo below for you of the dimensions of the Buyers Products Hitch Plate with 2" Receiver Tube - Ford # 3371809060A. view full answer...
According to Buyers Products, their # 3371809035A hitch will fit a 4500 / 5500 Top Kick as long as it has the same 34 inch measurement inside to inside of frame. view full answer...
I have a solution for you but the Buyers Products Hitch Plate for Pintle Mounting item # 3371809030B only fits 1999 and newer Ford F-350's. For your 1986 F-350 Cab and Chassis you will want the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper item # 3371809050. This hitch plate is made to attach to frames that are 34" wide.
I attached a picture of a diagram I made that will show you the dimensions of this hitch plate.
I have also linked a review video below. view full answer...
The width of the tab you marked in your picture is 2.9" and the height is 6.32". I have attached the full dimensional drawing of the # 3371809065 below for your reference. view full answer...
If your 2008 Chevy Silverado initially came with the cab and chassis body then you should be able to use the Buyers Products Hitch Plate with Receiver Tube - Chevy/GMC # 3371809065. This is for the 3500 model and measures 17" tall by 62" wide. You'll need to check on the fitment on your end since this is a sort of fabrication for the installation.
I've attached a review video for you to check out. view full answer...
The Buyers Products Hitch Plate with Receiver Tube - Dodge/RAM part # 3371809067 is designed for 2007+ models. The only option we have for the older models is the Buyers Products Fabricators Hitch Plates like part # 3371809040 which requires custom fabrication i.e. drilling and welding. view full answer...
The Buyers Products Black Receiver Tube part # 337RT25808B isn't made in the USA but the Gen-Y Weld-On 2" Receiver Tube part # 325-GH-003 is and you can cut it down to the exact length you need and paint it. view full answer...
The best option we offer for installing standard trailer hitches on semi-tractors is with the Buyers Products Fabricators Hitch Plates which will be welded to the back of the frame with extra bracing and gussets. This will require professional installation from a metal fabricator. There are many sizes for these plates such as part # 3371809027A which is 34-1/2" wide x 25-1/2" tall. I have attached the other size options below.
The standard 2" can be had using the Buyers Products Black... view full answer...
The horizontal measurement from your photo for the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 is 11". The vertical measurement you're looking for is 12-1/2". I have added these to the photo below for your reference.
view full answer...
I would be happy to help you with that. I went out to the warehouse and took some measurements of the Buyers Products Hitch Plate with Receiver Tube - Chevy/GMC item # 3371809065. The distance between the two wings on the top outside edge of the hitch plate is 35". We don't have a schematic but I made a diagram of some of the other dimensions of this hitch plate. view full answer...
I do have an option but all of the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumpers like part # 3371809055 are designed for cab and chassis models which have the narrower frame rails. If you want to install one on a standard model which has the wider frame rails you'll need to go with one of the universal plates like the Buyers Products Fabricators Hitch Plate part # 3371809040 and make some custom brackets. view full answer...
The size of the bolts you'll end up using with the Buyers Products Hitch Plate part # 3371809060A will depend on the application which is why they are not included. The other option is that you can have the hitch plate welded in place. view full answer...
The thickness of the tube of the Curt 18" Combo Bar with 2-1/2" Trailer Hitch Receiver # C49511 is 1/4" so the tube itself is 3" square. I have added a link to a video review for you to check out as well. view full answer...
I checked with Buyers Products and the overall length of the Hitch Plate part # 3371809065 is 62 inches, height is 17 inches and width is 7-1/4 inch. The weight is 102 lbs.
view full answer...
It sounds like you're looking for an articulating coupler.
For the trailer side of the equation, use # 336TS504 for an A-frame coupler. For an adjustable channel tongue use # 336TS502. If you need a 2 inch channel tongue go with part # 336TS528, # 336TS506 for a 2-1/2 inch channel tongue, or # 336TS508 for a 3 inch channel.
For the vehicle side, there are several different drops available. For a zero rise/drop, use # 336VS501. For up to a 4-1/4 inch rise or drop, use # 336VS503505... view full answer...
I have spoken with Buyers Products in the past about the Buyers Products Fabricators Hitch Plate part # 3371809043 and they have stated that the reason that they do not rate the plate for a specific weight capacity is becuase this will largely be dependent on how securely it is mounted. The highest rated pintle hook we offer for this is the Buyers Pintle Hook with Mounting Kit part # 33710042 which is rated for up to 40,000 lbs so the above plate will handle this so long as it is attached... view full answer...
The Buyers Products Fabricators Hitch Plate part # 3371809027A is designed to work with pintle hooks that have a 1-3/4" x 3-3/8" wide bolt pattern like the Bolt-On Pintle Hook part # 63016. This is a standard pattern that most pintle hooks use so if you have a few already they should fit. view full answer...
The Buyer's Products # 337RT255818 receiver tube is constructed of 3-1/8 inch square metal tubing with a 1/4 inch wall thickness, as shown in the provided photo. I've linked to a product description video featuring the
# 337RT255818 receiver tube. view full answer...
The Buyers Products Fabricators Hitch Plate # 3371809027A will work with the 40,000 pound Pintle Hook # 33710042. This will be the highest capacity pintle that can be used in unison. Both the # 337PH50 and # 337PH55 have odd bolt hole spacing and will not fit together with the # 3371809027A, unfortunately. view full answer...
The Buyers Products Hitch Plate with Pintle Mount to fit GM C4500/C5500 part # 3371809039A measures 62-1/2" long edge to edge and 22" tall. It fits 3" frame widths. I have attached a diagram of all of the measurements of the pintle hook plate for your reference. This pintle hook plate and other that we carry will require welding. This will work with cab and chassis with 34" frame width. It has a 20,000 pounds weight capacity.
view full answer...
The highest capacity pintle hook that can fit on the Buyers Products Fabricators Hitch Plate - 3/4inch x 34-1/2inch x 22-1/2 Item # 3371809027A you referenced is the part # 33710042 which has the non-offset mounting bolts like you mentioned and has a 40k capacity. view full answer...
The Buyers Products Black Receiver Tube part # 3371804055 has a vertical set of holes which are 3-1/2" apart on center and a horizonal set which are 3-3/8". I have attached a dimensions drawing from the manufacturer below. view full answer...
If the tow vehicle has a 2 inch hitch, a receiver tube like # 337RT25836B would not fit into it, as its outer dimension is roughly 2-1/2 inches square. If your tow vehicle has a 2 inch hitch the longest extension we have available for it is 18 inches, part # C45796. The extender would reduce the tongue weight capacity of your hitch by half, so be aware of that.
If the hitch has a 2-1/2 inch receiver, the # 337RT25836B would fit, but you might need to lightly sand off some of the powder... view full answer...
I reached out to Buyers Products and they said that the additional 1/4" on your 1994 Kodiak C6H042 is fine. You will be able to install the Buyers Products Hitch Plate with Receiver Tube - Chevy/GMC # 3371809065 without any issues. view full answer...
The hole spacing of the Buyers Products Fabricators Hitch Plate # 3371809042 that you referenced is the same as the standard pintle mount bolt pattern which is 1-3/4 inches apart vertically and 3-1/2 inches apart horizontally. view full answer...
The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 is designed or flatbeds and flatbed dump trucks. While it is ready to mount on Ford trucks, there is some drilling required for GM trucks. This hitch is a universal fit so while I can't really confirm a fit on your 1987 Chevy R30, I have attached a photo showing some of the basic dimensions that you can compare with your truck. If you have any other questions please let me know! view full answer...
Yes, the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with Pintle Mount # 3371809050 that you referenced does fit the flatbed/dump bed you have on your 2000 C6500. According to Buyers Products this fits your chassis but will require some drilling. view full answer...
The Buyers Products Fabricators Hitch Plates like part # 3371809042 are not given a weight capacity by the manufacturer. This is because the weight capacity will largely be dependent on how securely it is mounted. The highest rated pintle hook we offer for this is the Buyers Pintle Hook with Mounting Kit part # 33710042 which is rated for up to 40,000 lbs so the above plate will handle this so long as it is attached correctly. view full answer...
The Buyers Products Hitch Plate # 3371809067 manufacturer specs are,
Width of the hitch plate is 34-1/16"
Length of the hitch plate is 15-1/4"
Thickness of the horizontal bumper is 2-3/8"
view full answer...
The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper # 3371809055 is designed specifically for flatbeds, flatbed dump trucks and cab-and-chassis trucks with a nominal 34-inch frame width.
I measured this hitch in our warehouse to give you its primary dimensions. Please refer to the linked photo that I prepared for you. view full answer...
I contacted the manufacturer and after some research they stated that the Hitch Plate for Pintle Mounting, Item # 3371809030B, will work with a 2019 Ford F-550. They looked over the changes that they know about from 2018 to 2019 and nothing seemed to be significant. However, they did state that they have not had an opportunity to actually mount the hitch plate to a 2019 Ford F-550 yet so they can not confirm with absolute certainty a fit.
view full answer...
The 5 sets of mounting holes on the Buyers Products Hitch Plate for Pintle Mounting - 1/2" x 15-1/2" - Ford # 3371809030B measure center to center at 3-3/8" and vertically 1-3/4".
The Gen-Y Adjustable 2-Ball Mount w/ 2" Stacked Receivers - Bolt On - 7-1/2" Drop/Rise - 16K # 325-GH-124 matches those mounting base plate hole dimensions just mentioned while the Gen-Y model # 325-GH-724 does not.
I have included a diagram and some video resources to help as well.
view full answer...
Your 2000 Chevy 3500 is not considered to be a medium duty truck so Buyers Products Hitch Plate with Pintle Mount # 3371809038A would not be the best option for you. For the 3500 we have # 3371809035A. But since they have to be welded on and bolted on you could technically use either one. I have linked videos of each for you so you can see how they compare to each other.
Capacity is given based on several factors including the vehicle it is being installed on, the design of the plate,... view full answer...
As long as the distance from outside to outside on the rear frame rails of your 1973 Chevrolet T-65 is 34 inches the Buyers Products Hitch Plate with Receiver Tube # 3371809065 is the correct size and would work well. It's designed to fit the style of truck you have though so I'd be shocked if yours didn't match this as the 34 inch frame is a very standard size. view full answer...
I think the best option we have for you is a universal weld-on hitch plate like one of the following that I have attached for you. We do not really have any direct fit hitch plates for you so I think this will be the best option we can offer. If you are not an experienced welder then I recommend taking both the hitch plate and your truck to one for installation. The hitch plates below all come with d-rings for the safety chains as well as gussets for added strength.
Buyers Products Fabricators... view full answer...
The hitch tube part # 337RT25836B that you referenced has a capacity of 20,000 lbs so if you were to use on your trailer that would weigh around 8,500 lbs you'd have plenty of capacity. Normally this would install on the vehicle side and be used with a ball mount to connect to a trailer but from a weight capacity standpoint like you asked about this would work well. view full answer...
Yes, the Buyers Products Hitch Plate part # 3371809060A fits the Ford 550 cab and chassis as long as the frame measures 34 inches wide. view full answer...
The outer tube dimensions of the Buyers Products Black Receiver Tube # 337RT25818B are 2-1/2" x 2-1/2" square. The length of the tube is 18" long. view full answer...
For a hitch opening to weld to your tractor the Combo Bar 6" part # E-9 would be a great solution for that. Then for a ball mount that has all three main sizes and even a clevis hook if ever needed the part # RP47FR would be a great solution that would cover everything. view full answer...
Buyers Products Hitch Plate with Receiver Tube # 3371809060A is indeed designed to fit the Ford cab and chassis trucks so it will fit your 1997 F-350 cab and chassis. I have several dimensions for this hitch plate but if they are not what you are looking for let me know.
The C-channel part at the bottom is 4 inches wide by 62 inches long. From the bottom of that channel to the very top of the hitch is 17-3/16 inches tall. The width of those side plates is approximately 5-1/2 inches front... view full answer...
We have the Draw Tite Class V hitch part # 41952 that fits the cab and chassis version of your 2020 Ram 3500 that your flat bed truck was built on. The Buyers Products that you mentioned would not fit. view full answer...
The solid bar extension we offer for a 2 inch hitch is the Curt Solid Steel 2 inch Hitch Bar, part # D30. This bar has a 5/8 inch diameter hole drilled in it and the overall bar length is 12 inches. We do not offer any trailer hitch extensions that have the weight capacity you are asking about.
Using any extensions in a trailer hitch does decrease the tongue weight capacity by 50 percent. view full answer...
As long as your truck originally was a cab and chassis model of truck before the dump bed was installed the Buyers Products Hitch Plate with Receiver Tube - Chevy/GMC # 3371809065 that you referenced would fit and work well. view full answer...
We have a Buyers Products Hitch Plate with Reciever Tube that does fit your 2019 Ram 5500 with the part # 3371809067, but the part number you mentioned does not fit so it would not work. view full answer...
While we don't have any custom fit hitch plates that fit your 2016 International 4300 we do have some universal mounts that would potentially work. You'd need to have a qualified welder install the kit.
The hitch plates below all come with d-rings for the safety chains as well as gussets for added strength.
Buyers Products Fabricators Hitch Plate: part # 3371809040 (1/2" thick x 34-5/8" wide x 15-5/8" tall)
Buyers Products Fabricators Hitch Plate: part # 3371809042 (5/8" thick x... view full answer...
We do not have this particular Buyers Products Hitch Plate part # 3371809039A in 5/8" or 3/4" but I do have an option for you. I recommend to use the Buyers Products Fabricators Hitch Plate part # 3371809043 which is 5/8" thick and comes with 2-1" forged D-rings and 2 weld-on gussets. view full answer...
Per Buyers Products' website, this hitch plate # 3371809061A measures 17.2" tall by 62" long at the bottom and 34-1/4" long at the top (measured from inside the mounting bars) and is constructed with 1/2" thick steel. I've attached a diagram as well. view full answer...
If your 2001 Ford F-450 features a flat or dump bed, the Buyers Products Hitch Plate Bumper # 3371809055 will fit and work well. This is designed for cab and chassis trucks like yours with the nominal 34" frame width. Hardware is not included with the hitch but this is something you can obtain from a local hardware store. Please note that Buyers states the hitch should be both welded and bolted to the frame, with at least two 3" welds per side.
I have attached a short video review that... view full answer...
The correct hitch plate for your 1995 Ford F-350 cab and chassis (these hitch plates will not work with pick-up trucks) is the Buyers Products Hitch Plate with 2" Receiver Tube - Ford # 3371809060A, Buyers Products Hitch Plate with 2-1/2" Receiver Tube - Ford # 3371809061A, or Buyers Products Hitch Plate for Pintle Mounting - 1/2" x 15-1/2" - Ford # 3371809030B.
I have added links to video reviews for you to check out as well. view full answer...
The outside dimension of the tubing that the # 337RT25848B Buyer's Products Black 2 Inch Receiver Tube is constructed of is 2-1/2 inches, so theoretically speaking it would possibly fit in a 2-1/2 inch receiver. However, it will likely be a very tight fit due to manufacturing tolerances and the fact that the
# 337RT25848B really isn't designed to be an adapter, but is rather principally designed as a fabrication part used to construct towing equipment.
In order to get the tube to fit... view full answer...
The outer tube width/height for the Buyers Products Black Receiver Tube # 337RT25824B is approximately 2-1/2 inches. It can vary slightly from one to the next due to the powder coating process. view full answer...
The Draw-Tite Combo Bar with 2" Trailer Hitch Receiver - 24" Long - Unpainted # 2852 is a 2 inch receiver that uses 1/4 inch thick steel walls. The receiver collar is 1/2 inch think for extra durability. view full answer...
From center to center, the bolt holes on the Buyers Products Black Receiver Tube # 3371804055 measure 3.5" vertically and 3.38" horizontally, as you can see in the accompanying photo. view full answer...
Are you saying you only have 12 inches of vertical room to work with to install the part # 3371809065? Or where exactly is the 12 inch limitation? view full answer...
The Buyers Products Plain Receiver Tube 2-1/2" I.D. x 8" Long # 337RT255808 has an inner diameter of 2-1/2" so it will fit that size of steel tubing without issue assuming that the shapes are the same. view full answer...
The only option we have for a pintle hook plate that has D-rings attached for the 1997 Ford L8000 Dump truck is the fabrication plates like part # 3371809042 part # 3371809043 and part # 3371809040. These plates come with the D-rings to be welded on with additional gussets for strength. Then you would use Buyers Pintle Hook with Mounting Kit - Bolt On part # 33710042.
We do not currently carry anything that is truly adjustable for the dump truck unless you have a 2" hitch. Then you... view full answer...
The Curt Solid Steel 2" Hitch Bar # D31 that you referenced is designed for someone who wanted to fabricate their own hitch mounted accessory. It's not a hitch extender so it would not reduce hitch capacity like a hitch extender would.
I attached an FAQ on hitch extender/adapters for you to check out as well. view full answer...
Extending the trailer tongue will not increase the trailer tongue weight, it may actually do the opposite but you may be able to shift cargo or your boat forwards to get the tongue weight back where you want it. Please keep in mind extending the tongue would need to be done by a professional welder. view full answer...
While we more than likely have a hitch or hitch plate that will fit your 2003 Freightliner Columbia, we do not have one that is confirmed to fit.
With that being said we still may have an option that will work for you, you will just need to measure the width of your frame.
If your frame is 34" wide then an option like the Buyers Products Hitch Plate with Receiver Tube # 3371809065 you were looking at would work. This hitch will need to welded and bolt to the frame.
If your frame... view full answer...
There is not a custom Buyers Products Hitch Plate for a 2000 Dodge Ram. Therefore, you'll have to use one of the Buyers Products Fabricators Hitch Plates like part # 3371809040 and fabricate the rest of the supports needed for installation. The plates will then accept most pintle hooks like the Buyers Products 10 Ton Pintle Hook part # 337PH10. view full answer...
I went to our warehouse to measure the actual wall thickness of the Tow Ready Combo Bar # 80948 and the similar Curt # C49480, both of which are 48-inches long with a raw finish.
With a digital caliper I measured the wall thickness of the Tow Ready combo bar as 0.20 to 0.21-inches and the Curt was the same. Since these items are not machined there may be some slight unit to unit variances, especially if you are talking about thousandths of an inch.
On the receiver end of these bars... view full answer...
For a regular extension that fits a 2 inch trailer hitch receiver the longest available is going to be 18 inches such as # C45796. In order to reach at least 30 inches you would then need to use a ball mount that measures at least 12 inches from the center of the hitch pin hole to the center of the ball hole.
But I do not know how much rise or drop you need to tow the trailer level. So what I did was include a link to the fixed ball mounts that would be long enough, as well as a link... view full answer...
I attached a picture that I edited that shows the dimensions of the Curt Hitch part # E17 that you referenced. The side bracket measures 4-1/2 inches tall by 5-1/2 inches long, and from the bottom of the bracket to the hitch opening is 2-3/4 inches. view full answer...
The Curt Solid Steel 2" Hitch Bar with Raw Finish - 10" Long # D29 you were looking at is meant to give you a starting point to make you own hitch accessory for a 2" trailer hitch receiver.
For towing you would need a ball mount with a hitch ball like the Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball # C45331 which has a 15000lb towing capacity, but keep in mind that you will be limited to the lowest rated component which could be the ball mount, the trailer hitch receiver, or... view full answer...
The Buyers Products Black Receiver Tube # 337RT25848B is a receiver tube and not an extension. It will not be able to slide into each other as the tubing is 2"x2" square tubing the entire 4' length.
You would be able to connect these with the Curt Solid Steel 2" Hitch Bar # D30 but it will require drilling a 2nd hole through the steel tubing and the hitch bar. It may be better to weld the hitch bar to the receiver tube with plug welds as this would be a stronger connection and it would... view full answer...
Unfortunately, our manufacturers don't offer a 2 inch hitch for your 2015 Honda Accord.
If you can remove the battery packs and somehow get the weight of the bikes down to 65lbs each or less, we have a solution that would work for you.
You'd first need a Class I hitch like the # C11681 which has a 200 lb tongue weight capacity. For a rack, the Thule EasyFold, part # TH903202 can accommodate 2 bikes weighing up to 65 lbs each with tires up to 3 inches wide. For tires up to 4-11/16... view full answer...
The Gen-Y Weld-On 2" Receiver Tube - 12" Long - Steel # 325-GH-003 has a tube thickness of 7/16 inch. The collar thickness is 1/2 inch and the collar length is 3/4 inch not including the weld bead on the back. view full answer...
I reached out to the manufacturer, Buyers Products, who told me an ICC bumper is NOT required on your truck in order to install the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with Pintle Mount # 3371809050 or the same bumper with 2" Receiver # 3371809055. view full answer...
The Buyers Products Hitch Plate with 2" Receiver Tube - Ford # 3371809060A you were looking at does not include the required hardware so you will need to source them locally. You will need to use Grade 8 hardware and also weld the hitch to the frame of the vehicle.
I included a video of the # 3371809060A for you to take a look at. view full answer...
The Buyers Products Hitch Plate part # 3371809061A is a universal weld/bolt-on hitch plate. That said, the dimensions are geared towards Ford F-350/450/550 trucks so if this is what you have it would be a great option. view full answer...
Besides the price difference the only real other difference is that the # C49480 and the # 80948 are made by separate companies. The Curt combo bar is # C49480 and the Tow Ready combo bar is # 80948. Tow Ready is a brand that is owned by a larger parent company named Cequent.
These companies compete with each other in the trailering market so it isn't uncommon to see two similar parts with different pricing.
To answer your question, some customers prefer one brand name over the... view full answer...
We do have some hitch bars but unfortunately, we do not have any stolid steel 2" hitch bars in a 30" length. The longest one we have is the # D36 you were looking at, which is a 24" length. We do have an Unfinished Receiver Tube # C49480 that is longer, but it is 48" so you would have to cut it down.
I also included a link to our full selection of hitch fabrication parts for you to look for the best solution for your application. view full answer...
I pulled the quick links and quick loop that you referenced as well as the safety chains, # 2118-605-04, that you purchased and found that the best option for you will be the 3/8 Inch Quick Link, # 6590-044-04. This quick link will fit through the safety chain links and the safety chain loop. The measurement of the opening of the quick link is 0.48 inches (31/64 inches) which is slightly larger than the 7/16 inch diameter of your chain loops (see photo).
I made a short video showing... view full answer...
According to Buyers Products, their # 3371809067 is indeed a fit for a 2021 Ram 3500 Chassis/Cab with a 10K GVWR. The hitch has a maximum gross trailer weight capacity of 20K.
If you click the provided link, you can see a product description video featuring the # 3371809067 hitch. view full answer...
The Buyers Receiver # 3371804055 can be used in quite a few applications. As to your school bus bumper, there really shouldn't be any issues. I will say, however, that you will want to make sure there is a good amount of support on the bumper, especially where the # 3371804055 is going to be installed. If it is a little lacking, I would suggest shoring it up with a few braces for added support. I should also mention that the bumper on your bus is most likely not rated to be towed with,... view full answer...
I went to the warehouse and measured, the wall thickness of the Buyers Products Black Receiver Tube part # 337RT25848B is 0.27". This has a maximum gross trailer weight of 20,000 lbs so you will not have any issues using it for your farm equipment. view full answer...
I went to our warehouse and pulled a sample of the Draw-Tite 24-Inch-Long Combo Bar # 2852 so that I could measure its outside dimension for you. The bar itself measures 2-9/16-inches on each side and the reinforced collar area at the end of the hitch tube measures 2-7/8-inches on each side.
I prepared for you a photo of this part with these dimensions noted. view full answer...
We do carry a range of hitch fabrication plates such as the Buyers Products Fabricators Hitch Plat part # 3371809040 which measures 34-5/8" wide x 15-5/8" tall. That said, these are universal in design as the end product requires modifications to fit the exact application. I don't have any options specific to a particular make or model but these are the same plates you do see installed on big rigs so what you need to do is choose the one with the best dimensions for your particular application... view full answer...
The longest a-frame coupler style would be a sleeve lock like the part # CA-5296-B. The width of it is 9-7/8 inches which you can use that dimension as a way to tell where it would fit on your trailer and then from that point out measure 16-1/4 inches to see how much additional length it would add beyond what you have now. view full answer...
We do indeed have shorter 2-1/2 inch combo bars available than the 18 inch long # 11029 that you referenced.
For a 12 inch long bar you can use part # 337RT255812 or for an even shorter 8 inch bar you can use # 337RT255808. I have attached a couple short video demonstrations on these bars that you can also take a look at. view full answer...
I do have an option for you but they do not offer a custom fit front mount trailer hitch for your 1985 Ford F-250. Instead, you would need to use something like the Curt Weld-On 2" Receiver part # E17 and then fabricate a cross tube and set of brackets to attach it to. This will be you only option in regards to a front mount trailer hitch but if you can tell me what you intend to use the trailer hitch for I would be glad to see if other options are available. view full answer...
I'm pretty sure I understand what you're wanting to do but I don't think we have exactly what you're looking for. The closest option we have will be something like the Brophy Hitch Extender # RHSE that measures 19 inches long (which represents the longest such extender we have available) along with a fixed ball mount like the Curt # D-26 that would insert into the extender for an extra 12-5/8 inches of length plus the desired hole for a hitch ball.
We also have the Lets Go Aero Flat... view full answer...
The wall thickness of the Buyers Products Plain Receiver Tube # 337RT255812 that you referenced is 1/4 inch which means it's outside diameter is 3 inch by 3 inch. view full answer...
Curt combo bar # C49360 does not have an official weight capacity rating because it is not an extension. They use this bar and others in the manufacturing of their trailer hitches which have a wide range of capacities. If you can tell me the intended purpose/amount of weight I can tell you if the combo bar will be able to handle it or if something else is needed.
But if you are looking for a 2 inch hitch extension then the longest that fits a 2 inch hitch and still has decent capacity... view full answer...
The Buyers Products hitch plate part # 3371809065 that you referenced is designed to be welded on by a professional. The bolts holes are there for you to hold the hitch in place for when it gets welded on according to our techs at Buyers Products. They do not provide any written instructions either as they want you to take it to someone with the experience and skills needed who wouldn't need them. view full answer...
As long as a qualified welder is used, a Safety Chain Attachment Loop like part # E950 could be welded to the receiver as shown in the photo I provided. Having an amateur welder weld it could result in the hitch being weakened. This would be the best and easiest solution for you.
There's no set distance that you should have it welded on the hitch at, but if you use the picture I attached as a guide you would be just fine. view full answer...
The # C49480 isn't a hitch extender. It's actually just a 48 inch long hitch tube for fabrication purposes.
If you had a 2-1/2 inch hitch the Reese extender part # RP45292 is 34 inches long and might work well for you. view full answer...
Go To Results