See what our Experts say about this CURT Hitch Fabrication Parts

• Will Curt Trailer Hitch Receiver Fit 2025 Ford Mustang GT With Active Valve Exhaust
  Hi Doug; the Curt Trailer Hitch Receiver # C45RJ is a pre-order item. Since it hasn't been fully developed we don't have any information on fitment restrictions yet. Once Curt finishes the hitch we will be able to answer that question. As of right now, they're the only company we know of developing a hitch for the 2025 Mustang. If you have a more immediate need for a hitch I recommend taking the # E-911 to a local fabricator to see if they can fashion a custom hitch for your Mustang GT.
  view full answer...
• Does etrailer Make Class I Hitch for 2024-2025 Nissan Z Sport
  Hi Randy; we do not make custom hitches here at etrailer and none of the typical manufacturers have one for your 2024-2025 Nissan Z Sport. What you can do is take the Combo Bar 6" with 1-1/4" Trailer Hitch Receiver # E-911 to a local fabricator and have them fashion a custom hitch for your vehicle. If you would prefer a 2" receiver the # E-9 is also available.
  view full answer...
• Availability of Trailer Hitch for 1993 Cadillac Allante
  Hi George; if it is a 4-door it looks like U-Haul makes a custom hitch for it but you will have to go through them. If it is a 2-door, or if the price seems too high on the other hitch for the 4-door, you can check with a local fabricator and see if they'll make one for you using # E-911. The only other option would be to use a trunk mount bike rack like the # 298-BK1910-BK or add a roof rack like # 298-SX6000B. With the roof rack you can use a bike rack like the Yakima FrontLoader # Y02103.
  view full answer...
• Solution for Trailer Hitch on 2021 Lexus ES 350 F Sport
  Hi Joseph; I'm sorry to say that none of the custom fit hitches for the 2021 Lexus ES 350 fit the F Sport trim. Also, there are no kits available to make them compatible. I don't have the specifics but it is likely a difference with the exhaust or you would have to butcher the rear bumper to make it fit. The only solution is to take a hitch fabrication receiver like the # E-911 to a local fabricator and have them fashion a custom hitch for your vehicle.
  view full answer...
• Solution for Carrying Bike Rack on 2017 Mitsubishi Lancer SE With Fore to Aft Muffler
  Hi Michael; I'm sorry to say that the Curt # C11479 also has the fore to aft muffler restriction. There are no custom fit hitches available that will allow you to carry a bike rack on your 2017 Mitsubishi Lancer. However, it may be possible to have a custom hitch fabricated locally using the # E-9 (2" receiver) or # E-911 (1-1/4" receiver). You will have to reach out to a local fabricator to see if they can make it work. If not, your only other option is to switch bike racks. You can use...
  view full answer...
• Availability of Class I Hitch for 2001 Audi TT
  Hi Tim; the Curt 11775 was discontinued back in 2022 and we no longer have any available. If you are unable to find one I recommend taking the # E-911 to a local fabricator. You can have them fashion a custom hitch to fit your vehicle.
  view full answer...
• Do You Have a Riser for My Thule Bike Rack for 1 1/4" Receiver to Gain More Clearance?
  Hello Michael, We only have a riser that goes from a 1 1/4" hitch to a 2", so you will need to use the Trailer Hitch Adapter - 1-1/4" to 2" Hitch - 4-1/2" Drop/5" Rise - 6-1/2" L # e93YR with a reducer, the Trailer Hitch Reducer 2" to 1-1/4" Trailer Hitch Receiver # e63YR. I would like to point out that the # e93YR will cut your tongue weight in half. Or you could get the Combo Bar 6" with 1-1/4" Trailer Hitch Receiver # E-911 and have a local fabricator weld you together a rise. Do...
  view full answer...
• Solution for Trailer Hitch on 2004 Mercedes-Benz CLK 320
  Hi Rosemary; I'm sorry to say there are no custom fit hitches available for your 2004 Mercedes-Benz CLK 320. The best solution for a hitch would be to take the # E-911 to a local fabricator. They will be able to fashion a custom hitch for your vehicle. What are you planning to use the hitch for?
  view full answer...
• Is There A Hitch Receiver For 2010 Cadillac CTS Wagon?
  Hey Greg, unfortunately it doesn't fit. Curt used to have one that fit - Class 1 Trailer Hitch, 1-1/4" Receiver, Select Cadillac CTS #11013 but it's been discontinued. You may be able to find left over stock on another site or a used one perhaps. Sorry about that. A custom welding shop could fabricate something with Combo Bar 6" with 1-1/4" Trailer Hitch Receiver # E-911 or Gen-Y Weld-On 2" Receiver Tube - 12" Long - Steel # 325-GH-003.
  view full answer...
• Is There a Trailer Hitch Receiver Option For a 2023 Mercedes E 450 All-Terrain Wagon?
  I'm having the same issue Henk, and I do not even see that Mercedes offers a factory receiver option for your 2023 E 450 All-Terrain Wagon. The only help I can offer is we do have the 2" # E17 or 1-1/4" # E-911 which you can take to a local fabrication shop who can weld you up a receiver. If you need to run any Auxiliary Lights # C53201 on your bike rack the Curt 4-Way # C59236 is a universal option which will allow you to splice into the factory tail light wiring.
  view full answer...
• Trailer Hitch Receiver For a 2008 Volvo C30
  Your 2008 Volvo C30 will need to have a custom receiver made as there is not a receiver that is confirmed to fit. The Curt Trailer Hitch Receiver # C11337 that you found is for the 2011-2013 model years. We have the Curt Weld-On 2" Receiver # E17 or Combo Bar 6" with 1-1/4" Trailer Hitch Receiver # E-911 to have a custom receiver made at your nearest customization shop. The Curt Upgraded Circuit Protected Powered Tail Light Converter w Hardwire Kit # C59496 can be used to allow for...
  view full answer...
• Thickness of the Combo Bar with 1-1/4" Trailer Hitch Receiver Part # E-911
  I spoke to my contact at Curt and they informed me that the thickness of the metal that is used on the Combo Bar with 1-1/4" Trailer Hitch Receiver part # E-911 is 3/16" thick. There are other dimensions of the combo bar on the product page if you need them. I have attached a review video for you as well.
  view full answer...
• Hitch Recommendations for a Scamp Trailer Bumper
  Depending on the dimensions of your trailer's bumper I believe we could have a solution for you that would not require welding. If you have a 4 inch by 4 inch bumper you could use the part # E-100. If you have 2x4 inch bumper you could use the # C19101. These have 2 inch openings though. For a hitch opening that measures 1-1/4 inch that would require welding on you would want the part # E-911. You will need to make sure that the bike racks you plan on using are rated for use on an RV. I...
  view full answer...
• Is There a Custom Fit Trailer Hitch Receiver For a 2019 Volvo S60 T5 Inscription?
  It appears you will need to have a custom receiver fabricated for your 2019 Volvo S60 T5 Inscription. We have the 1-1/4" # E-911 or 2" # E-9 receiver tube that you can use to have a receiver fabricated. Currently none of our aftermarket manufacturers are producing a receiver for your Volvo. I was able to verify with Curt that their T-Connector Vehicle Wiring Harness # C56224 will fit your Volvo and give you a 4-way flat connector. This will connect to the tail lights on most small trailers...
  view full answer...
• Is There a Trailer Hitch Receiver Available For a 2023 Infiniti QX55?
  Currently Bob, the only trailer hitch receiver I see available for your 2023 Infiniti QX55 is the factory option. It is a 2" receiver opening which most bike racks or use a Reducer # HT02 if you already have a bike rack for a 1-1/4" receiver. We do have a 1-1/4" Hitch Tube # E-911 if you wish to have a receiver fabricated with the smaller opening.
  view full answer...
• Attachment of Winch Receiver to 1996 Jeep Cherokee Sport
  The easiest way to install a 2 inch receiver, front or back, on your 1996 Jeep Cherokee Sport is to use a custom fit receiver hitch. I would recommend the Draw-Tite Class III Receiver Hitch, item # 75054, for the rear and the Curt Front Mounted Receiver Hitch, item # 31084, for the front of your vehicle. If you want to use the Combo Bar 6" with 1-1/4" Trailer Hitch Receiver, item # E-911, for your jeep it would require fabrication of a mount and welding to secure it to the Jeep good enough...
  view full answer...
• Availability of 1-1/4-Inch Combo Bar for Hitch Fabrication on Antique Tractor
  I can offer you a better option for installing a 1-1/4-inch receiver tube on your antique tractor. Curt offers several lengths of their 1-1/4-inch combo bar, which is a raw steel product ready for weld-on installation. Part # E-911 is 6-inches long, part # E-912 is 12-inches long and part # C49524 is 24-inches long. One of these will cost far less than a custom-fit hitch. Also, if you used a custom hitch like the one for a Corvette any modifications would void the item's warranty, so...
  view full answer...
• Recommended Hitch Adapter For 2" Receiver To Carry a 1-1/4" Bike Rack Higher On My Vehicle
  I recommend having a 2" to 1-1/4" hitch riser built for your Yakima Dr. Tray Bike Rack. Having a custom built riser will allow you to move the rack up for better ground clearance and keep it as close the the rear of your vehicle as possible. The Curt Solid Steel 2" Hitch Bar # D31 can be welded to the 6" Combo Bar 1-1/4" Receiver # E-911 with some steel plate or tubing. A local welding shop should be able to provide the additional material necessary to get the receiver tube where you...
  view full answer...
• Receiver Tube For Custom Trailer Hitch Receiver on a 2021 Cadillac CT4
  You may be able to have a custom receiver made for your 2021 Cadillac CT4 using a Curt Weld-On 2" Receiver # E17. I do not see that any manufacturers are making a receiver that will fit your CT4 and the AT4 chassis is different so you will not be able to use one from that vehicle. A customization shop may be able to make you a receiver with the part above. We also have a 1-1/4" Receiver Tube # E-911 if you want the smaller tube for better ground clearance.
  view full answer...
• Recommendation For a Quick Connect 1-1/4" Receiver To Attach On Tractor Drawbar?
  I think I will have a solution for you as the 1-1/4" Receiver Attachment # 391RR1 is only designed to lock into the block on a Stealth Hitches receiver. There would be no way to secure the end on your tractor. Instead we have the 6" # E-911 or 12" # E-912 receiver tubes. This would allow you to be able to fabricate a type of mount for the receiver or possibly weld it to a Curt Clevis Pin # C45803 which is a 1" diameter. You would need to add some steel to the front or rear which would prevent...
  view full answer...
• Can 2 Inch Receiver be Welded to Buyers Products 2 Heavy-Duty Channel Tongue Coupler 3370091560
  You could weld on a receiver tube to the top channel part of the Buyers Products coupler # 3370091560 if you wanted to. Keep in mind though that this coupler is zinc plated so any welding should be done by someone with experience welding with zinc plated steel in a well-ventilated area. I am not sure what you will be using the receiver for but there are some products that mount to the front of a trailer and have a 2 inch receiver for accessories like a bike rack. We have the Bike Bunk,...
  view full answer...
• What are the Dimensions of the Combo Bar 6 inch
  The overall width of the Combo Bar 6 inch with 1-1/4 inch Trailer Hitch Receiver, part number E-911, is 1-5/8 inches. Other dimensions of note are 4 inches from center of hitch pin hole to back of the bar, 2 inches from center of the hitch pin hole to the front of the collar and the overall length is 6 inches.
  view full answer...
• What 6 inch Combo Bar Can C49524 Fit Into
  The hitch combo bar part # C49524 could fit into the part # E-9 but not into the # E-911 as they are both the same size.
  view full answer...
• Motorcycle Hitch For 2004 Honda VTX1300R
  We don't carry any motorcycle hitches, but we do have the combo bar to get you started on a custom hitch. I recommend the Curt Combo Bar 6" with 1-1/4" Trailer Hitch Receiver, # E-911, to have a certified professional welder make you something for your bike.
  view full answer...

Do you have a question about this Hitch Fabrication Part?