Replacement Rear Wheel Assembly Availability for Yakima Holdup Bike Rack

Question

Question:

Im looking for the Replacement Rear Wheel Assembly for Yakima HoldUp Bike Carriers, but all I can find on your site is the front tray see link below. I would need part 8890281

asked by: Jeff J

1

Helpful Expert Reply:

We have the exact part you are looking for, part # 8890281. This is the replacement rear wheel assembly for your Yakima Holdup bike rack. The part # 8890280 is the front wheel assembly.

expert reply by: Jameson C

1

Answer 1

You certainly can switch around the platforms on your Yakima HoldUp Platform Bike Rack #Y02443 in order to change the orientation of the bikes. I spoke with my contact at Yakima and he confirmed this can be done to avoid a conflict on the vehicle,…

view full answer...

Answer 2

It looks like you have the standard version, the Yakima HoldUp #Y02443. The replacement front arm #8880833 is only for the HoldUp EVO #Y02479 bike rack. You are correct that in your case, you will need to replace the entire front wheel assembly…

view full answer...

Answer 3

The difference between the two parts you referenced is that the Replacement Front Wheel Assembly #Y90197 is the track for the front side of the rack and the Replacement Rear Wheel Assembly #Y90198 is for the rear track of the rack. If you are unsure…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Rear Wheel Assembly Availability for Yakima Holdup Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching