Replacment Plastic Endcap For Stromberg-Carlson RV Ladder

Question

Question:

I am looking for end caps on a Stromberg Carlson 8540-nt ladder steps.

asked by: James

0

Expert Reply:

The replacement endcap for the ladder rung on your Stromberg-Carlson 8540-NT is part # 8540-CP.

This replacement endcap will also fit the 8540-NTB ladder as well.

expert reply by: Jeffrey L

0

Answer 1

I cannot confirm that the Replacement Plastic Ladder Rung End Cap on Stromberg Carlson RV Exterior Ladder - Qty 1, #8540-CP will fit your Kemberly Inc. RV ladder. However, the rough measurements are 2 inches in length by 5/8 inch wide and 1 inch…

view full answer...

Answer 2

The Replacement Plastic Ladder Rung End Cap, part #8540-CP is designed to fit Stromberg Carlson RV exterior ladders so I cannot confirm that it will fit your Kemberly ladder on your 2010 Montana fifth wheel. These caps measure 2-inches long, 5/8-inch…

view full answer...

Answer 3

Hey Darrell yes, the Replacement End Cap for Stromberg Carlson Exterior RV Ladders #8540-CP can be used to replace the older Kimberly ladder end caps. Attached is a review from a neighbor who used these caps to replace their Kimberly ladder end caps…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Replacment Plastic Endcap For Stromberg-Carlson RV Ladder

Product Page this Question was Asked From

Continue Researching