How to Install Brake Controller in a 1996 Dodge Van B2500

Question

Question:

Hello, I have a 1996 Dodge B2500 van Does this model have a factory brake control connector under the dash or anywhere so that a wiring harness connector plugs up to it and the trailer brake controller? If so what harness connector part # is required Thank you

asked by: Rodney

0

Expert Reply:

You would need to hardwire a brake controller to your 1996 Dodge B2500 van as it does not have a brake controller install port under the dash like some vehicles do.

You will need to start with a 4-way (if you do not have one). For that you would want the # C59236.

From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.

For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup.

expert reply by: Jameson C

0

Answer 1

It sounds like you may already have a 4 way connector on your vehicle, which is half of the battle. In order to operate the Curt Echo Mobile Wireless Brake Controller #C51180 you will need an almost fully functional 7 way connector; using something…

view full answer...

Answer 2

We have all of the wiring you need for your 1996 Ram, but there is no all-in-one harness available. First I recommend part #HM40975-11998. This is a 7-pole and 4-pole trailer connector with the bracket and wiring. This will hardwire to the existing…

view full answer...

Answer 3

On a 1996 Dodge Ram that came with a factory 4-Way trailer connector there is a factory harness you can plug into to install a brake controller. The harness is located underneath the dash, to the left of the steering column, taped to another harness…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How to Install Brake Controller in a 1996 Dodge Van B2500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching