Will The Curt Class V 2 Inch Hitch # C15445 Fit A 2011 Ford F450 Cab And Chassis

Question

Question:

I need to find a 1,600/16,000 hitch for a 2011 Ford F450 Chassis cab with an Omaha utility body on it.The rear bumper is 3 lower than the bottom of the truck frame. From the end of the frame to back of the bumper is 13. We need install a pintle/ ball hitch.

asked by: Bernie R

0

Expert Reply:

The Curt Class V 2 Inch Hitch # C15445 is listed to fit a 2011 Ford F-450 Cab and Chassis with 34 inch wide frame.

I am sending a link to the installation instructions of the Curt hitch.

If you will be needing a pintle hook mount with a long shank I would recommend the Tow Ready Pintle Hook Mount # 63059. This mount will have a shank length of 11-3/8 inches from the center of the hitch pin hole to the end of the shank.

You will also need the pintle hook and ball combo that will bolt to the mount. If you need it with the 2 inch ball you will use the Tow Ready Pintle Hook Combo With 2 Inch Ball # TR63011. If you need the 2-5/16 inch ball you will use the Curt Pintle Hook Combo With 2-5/16 Inch Ball # C48200.

expert reply by: Jeff D

0

Answer 1

The Curt Trailer Hitch Receiver part #C15445 which is a fit for a Ford F-Series Cab and Chassis has a drop of 5-1/2" when measuring from the top of the mounting flange or bottom of the frame to the top cross tube. I have attached a photo of this…

view full answer...

Answer 2

Hey John, do you mean from left to right what is the dimension? Or front to back? The Curt hitch part #C15445 is designed to fit a 34 inch wide frame which is the size of cab and chassis trucks. The standard truck frame width is 37 inches. I believe…

view full answer...

Answer 3

B&W hitch #BWHDRH25122 is designed to fit many trucks including the 1967 Ford F-350 as long as it has (or had) a stock factory bumper. Most of the trucks of that era had a 34 inch frame width which this hitch will fit. But to answer your question…

view full answer...

Answer 4

I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item #C15845. I have attached a couple of diagrams with the dimensions of this hitch on them. From the center of the back bolt to the front of the receiver is 26" The…

view full answer...

Answer 5

As long as the 34 inch width dimension you took was from outside to outside on the frame channels the Curt hitch part #C15445 will fit as that's the frame dimensions it was designed to fit.

view full answer...

Answer 6

From the top of the mounting plates to the top of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25124 receiver is a 5-1/4" drop and then from the rearmost bolt hole to the end of the receiver is 10-7/8" (see attached).

view full answer...

Answer 7

I spoke to my contact at Curt and he informed me that the Curt hitch #C15317 center section measures 31-5/8 inches. The center to center mounting hole width with the flanges attached is 34-7/8 inches. He also informed me that the flanges on the…

view full answer...

Answer 8

What you will want to do is measure the distance between the mounting holes on the frame of your truck to see if the Curt hitch part #C15300 will fit. If the holes are 36 inches apart on center then this hitch will fit and work well.

view full answer...

Answer 9

The width of your frame indicates that your 2012 Ford F-450 is most likely a cab and chassis model which has the frame width a few inches than a standard truck bed. But if you can measure the distance between the mounting holes on the frame of your…

view full answer...

Answer 10

Thank you for the photo! What you have there is a deep drop or "cowboy" bumper. So, for a 2 inch trailer hitch that is confirmed to fit your 1989 Ford F-250 XLT Lariat with the deep drop bumper, I recommend the Curt #C15511. This 3-piece…

view full answer...

Answer 11

I would be happy to and thanks for the pictures! The B&W Heavy-Duty Trailer Hitch item #BWHDRH25122 measures 5.4" from the top of the frame brackets to the top of the receiver and 19-1/2" to the back of the receiver from the last bolt.…

view full answer...

Answer 12

I spoke with my Curt representative, who tells me that the front face of the receiver would sit 10-3/4 inches rearward of the rear-most mounting hole. If you find the rear most mounting hole in the underside of the frame member and measure 10-3/4…

view full answer...

Will The Curt Class V 2 Inch Hitch # C15445 Fit A 2011 Ford F450 Cab And Chassis

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching