Parts Required to Install Thule Square Bar Roof Rack on 2016 Jeep Grand Cherokee

Question

Question:

Is there a bracket to attach Thule square bars to a 2016 jeep grand Cherokee? Thanks

asked by: Jim H

0

Expert Reply:

There is a Thule square bar roof rack system made for your 2016 Jeep Grand Cherokee if it has the E Group Package with flush mounted roof side rails that run front to back.

This system uses 60-inch Thule load bars # TH712500 along with Traverse feet # TH480R and the vehicle-specific fit kit # THKIT1656. If you have 60-inch or longer Thule square load bars you can order the other two components to install those bars on your Grand Cherokee.

If on the other hand your GC has a bare roof then there is no Thule rack solution but the Yakima racks for that type of roof configuration are shown on the linked page.

expert reply by: Adam R

0

Angel R.

6/24/2020

Will this attach to the existing flush mounted bars or will it just attach to the door frames?

Chris R.

6/27/2020

The Thule Square Bar setup mentioned above utilizes mounting feet that will attach to a bare roof (and clamp to the door frames like you mentioned). To mount to those rails you'll use the Square Bar system that consists of parts # TH712400, # TH460R, and # THKIT3142.

Answer 1

The 5th wire on a 5-Way flat connector is intended to connect to the vehicle's reverse light circuit. This is for the exact situation you described, so the 5th wire can signal a surge coupler's electric reverse lockout. If you need a 5-Way…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Parts Required to Install Thule Square Bar Roof Rack on 2016 Jeep Grand Cherokee

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching