What is Overall Height of Timbren SES Kit # TGMRCK25D

Question

Question:

i fell like my truck is already sagging because i have a 60 gallon diesel tank /tool box combo in my bed my question is how tall are the timbren ses for a 2014 ford f-250 fx4?

asked by: Will B

0

Expert Reply:

Overall height is 5-3/16 inches.

That means that once installed, the double convoluted springs from the Timbren SES Kit, # TGMRCK25D, will sit 5-3/16 inches below the jounce bumper holder on the frame. The outer diameter of these springs is 4-5/16 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hey Thomas. I wouldn't say ones better than the other and they have identical installation processes as far as removing the shock tower assembly. It has to come off for both on your truck. The main differences between the Timbren item #TFF350SD4…

view full answer...

Answer 2

I had the Timbren Front Suspension Enhancement System #TFF350SD4B measured and it will be 6-5/8 inches from the top of the bracket to the bottom of the jounce. This is also designed to fit a 1999 to 2004 Ford F-250, F-350, and F-350 Cab and Chassis.

view full answer...

Answer 3

Yes, you are on the money with the fits. The Timbren Front Suspension Enhancement System #TFF350SD2 is a fit for the 2-wheel drive model of the 2003 Ford Excursion, while the Timbren Front Suspension Enhancement System #TFF350SD4 is a fit for the…

view full answer...

Answer 4

We have two Timbren rear suspension kits that fit your 2020 Ford F-250 we have the standard duty #TFRTT350J which has a spring height of 3-9/16 inch and a bracket height of 2-3/8 inches. The severe duty #TFR250SDJ is 3-5/8 inches tall and has the…

view full answer...

Answer 5

The Timbren kit #TFR250SDJ does not require a mounting plate above the axle as it is designed to contact the round the plate that is currently on the axle that is mounted below the spring pack. I would recommend sticking with this kit even though you…

view full answer...

Answer 6

I went out to the warehouse and pulled Timbren kit #TGMRCK15S to take some measurements for you. The overall height of the spring is 5-1/8 inches and the overall width is 4 inches (diameter). Timbren does make some 1 inch spacers, #A25723-90AH00,…

view full answer...

Answer 7

In regards to the Timbren Suspension Enhancement System part #TFR250SDJ which is a fit for a 2019 Ford F-250, these will fit lifted applications but you'll need to add spacers to make up the difference. The Timbren Spacer part #TA25722-90P00 for…

view full answer...

Answer 8

Hey Mike, I believe you are asking about the height of just the blue spring of the part ##SS68DR SSR-623-40 which is 4 inches. Otherwise it sounds like you are asking about the distance from the top of the mounting bracket to the bottom of the spring…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

What is Overall Height of Timbren SES Kit # TGMRCK25D

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching