Is the Mounting Style of the Timbren DR1500DQ Secure Will Timbren Fall Out of Cup

Question

Question:

Any problem once their seated of them falling out because they are simply pressed up into the bump stop mount?

asked by: Jerry T

0

Expert Reply:

We haven't had any issues with the Timbren part # TDR1500DQ coming out of the bump stop cup when used.

The factory bump stops are also pressed in and they don't have a tendency to fall out either.

expert reply by: Jameson C

0

click to enlarge

Steve P.

3/9/2020

I have the same concern. I just installed mine today and the first time I pressed them into the cup holder they fell out. So I put two blocks under the item and let the vehicle down hard on the axle and they stayed in. My question is, I noticed that the flat piece that the rubber stop rides on when the weight of the vehicle pushes down under load isnt flat and it has a slight angle to it. It looks like it is going to push the rubber stop to the side and then eventually come off? Is there any fastener type glue or epoxy that would hold it in place. If the item falls out is it warranted?

Chris R.

3/11/2020

We honestly haven't heard any instances from customers where their Timbren Springs fell out of the bump stop cup. The wood block method you used to get them fully seated is a great solution (we actually did this during our install on the 16 Ram) and you don't need to worry about them coming loose over time. I don't recommend using any glue or epoxy to secure them into place as this could affect their overall performance. The Timbrens do come with a limited lifetime warranty.

Oli

6/8/2020

Hi, i bought dr1500dq for my Ram 2017 sxt and there is no cup on the Truck to receive the timbren, the original bump only holds on a pipe about two inches, Do i bought the good ones or is There another way to install Them?

Chris R.

6/11/2020

Do you happen to have the Regular Cab model Ram 1500?

Answer 1

The correct Timbren suspension enhancement fit for your 2022 Ram 1500 will actually depend on the cab style of your truck. The Crew Cab and Quad Cab are different fits than the Regular Cab, so you'll want to choose the right one based on that: -…

view full answer...

Answer 2

Yes, the Timbren Rear Suspension Enhancement System part #TDR1500DQ is a confirmed fit for the rear of your 2019 Ram 1500 Laramie Crew Cab. The Timbrens are very easy to install as there are no tools required and they will do an excellent job of…

view full answer...

Answer 3

The Timbren kit part #TDR1500DQ that you referenced is a confirmed fit for your 2017 Ram 1500 and would be a great option to give you additional suspension support when you are carrying a lot of weight. Since you have a lifted truck though you will…

view full answer...

Answer 4

If you have a 2019 Ram 1500 that is the standard pick-up truck, the correct Timbren system is the Timbren Rear Suspension Enhancement System #TDR1500DQ, which were designed for standard trucks. The difference between these and the Timbren System…

view full answer...

Answer 5

The best Timbren Suspension Kit for your 2019 Ram 1500 2WD is the Rear Springs #TDR1500DQ. These will provide plenty of support for the tongue weight from your new trailer, as they have robust 8,600 pound weight capacity. I'm not sure how tall…

view full answer...

Answer 6

In a word, no, the warranty of your 2020 Ram 1500 will not be voided with the use of the Timbren Rear Suspension Enhancement System #TDRTT1500 or #TDR1500DQ. You are protected by what is called the Federal Magnuson-Moss Warranty Act. This act says if…

view full answer...

Answer 7

With Timbren Suspension Enhancement #TDR1500DQ installed in your 2014 Ram 1500 there will be a slight gap between the bottom of the springs and the axle so the unloaded ride height of the truck will be the same. Take a look at the picture I have…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Is the Mounting Style of the Timbren DR1500DQ Secure Will Timbren Fall Out of Cup

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching