Solution for Lost Plunger for Esco Model 2010 Breakaway Switch

Question

Question:

I have an esco model 2010 breakaway switch which I need to replace the plunger. I can only get the new o e I about a1/4 of an inch. Is there an easy way to re the plunger?

asked by: David H

0

Expert Reply:

The easiest solution I can provide is to just replace the entire switch with the part # 420000 that you referenced. Trying to replace just the plunger can be challenging and since all of the switches are basically universal it's just easier to replace the whole thing.

expert reply by: Jameson C

0

Answer 1

The B&W Continuum Weight Distribution System part #BW78FR requires at least 24" of space on the frame directly behind the coupler and along the side a few inches back from there. This works with most trailers but for some it will not and,…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

Welcome back Belinda! The Andersen Weight Distribution Hitch w Sway Control - 4" Drop/Rise - 16K GTW, 1.6K TW #AN33VR may work for towing your Grand Design Imagine XLS23LDE with your F-250. However, when we tested it a while back, we didn't…

view full answer...

Answer 7

Hey Frank. I can give you the dimensions of the shank on the B&W Continuum item #BW28FR but you're going to need to take the measurements on your Silverado 3500 to confirm the tailgate will open. From the hitch pin hole to the center of the…

view full answer...

Answer 8

Hey Tony! Yes, the Weigh Safe True Tow Weight Distribution Hitch #WS37RR is a good choice and would have the proper rating for your setup. The smaller 1.2k TW model is going to be rated too low, or right on the edge, once you factor in propane,…

view full answer...

Answer 9

That is definitely a feature which worries me about the B&W Continuum Weight Distribution System #BW78FR. While there is not a specific measurement I can give you as the bars move up and down depending on the load placed on the bars, B&W…

view full answer...

Answer 10

Hey Jon, I have a solution for you but I would not recommend the Andersen Weight Distribution system part #AN33VR for your 2025 Brinkley Z Air 297. What we have found is that the Andersen system does a decent job with lighter weight trailers but for…

view full answer...

Answer 11

Hey Tim, thanks for reaching out! The .75" sag you're seeing is acceptable, that will not have much of an effect on drive quality at all. If you'd like to totally level out your ride, then add the Air Lift LoadLifter 5000 Ultimate Air…

view full answer...

Solution for Lost Plunger for Esco Model 2010 Breakaway Switch

Featured Help Information

Miscellaneous Media

Continue Researching