Distance from Center of Pin Hole to End of Receiver on Curt Combo Bar E-9

Question

Question:

I cant believe nobody has asked this, but what is the distance from the end of the receiver to the center of the 5/8inch hole? Thanks!

asked by: Chris

0

Expert Reply:

According to my calculations the distance from the center of the pin hole to the far end of the shank on Curt combo bar # E-9 is 3-1/2 inches. The bar is 6 inches long overall so from the center to the face of the receiver is 2-1/2 inches.

expert reply by: Michael H

0

click to enlarge

Answer 1

We have winches that can have power drills attached to them to make cranking a bit easier. For this, you'd want something like the Dutton Lainson Worm Gear Winch #DL11004 which does have the hex drive option.

view full answer...

Answer 2

The Dutton-Lainson DL2000 is indeed different as it is an earlier model of the DL2000A; I checked with Dutton-Lainson and they do not offer replacement parts for the older DL2000, and said that parts are not interchangeable between models. So while I…

view full answer...

Answer 3

When considering the rear bumper and spare tire clearance when using the Kuat Beta - Aluminum Folding 2 Bike Rack for 2" Trailer Hitches #B202-2, it truly depends on two different factors: where your hitch installs on your Wrangler and the width…

view full answer...

Answer 4

The issue that you are going to run into if you use Roadmaster Dual Hitch Extender #RM-077-2 is the tongue weight capacity will be reduced 50 percent. However, if you use a ball mount like #D210 you will get a 6 inch rise and 7-1/2 inch extension…

view full answer...

Answer 5

We carry a very handy 2 inch ball mount for this exact application. The part is #D210. The ball mount slides and pins into your hitch and the top receiver will accept 2 inch bike racks and hold them above the ball. The Ball Mount has a 500 lb tongue…

view full answer...

Answer 6

Ideally a hitched trailer will be level to the ground. We often recommend starting off with the hitch ball being a bit higher - an inch or so - than the top of the coupler on the level trailer since once hitched there will be a degree of squat in the…

view full answer...

Answer 7

Hi Morgan; nobody has made a front hitch for the Suburban for several years now and the #EH58RR only fits the Silverado 1500. If you want a front hitch the best option would be to take the #E-9 to a local fabricator and have them fashion one for you.…

view full answer...

Answer 8

Hey Jeremy. We do not carry the F47260K. It looks like it's a replacement Master Cylinder for Tie Down Models 66 - 70 - 80 Disc Brake actuators. Not sure if it'll work with the 70lc brake actuator. I do not have any replacement parts for a…

view full answer...

Answer 9

Hey Brad, thanks for reaching out! What are the dimensions of your tail lights? The numbers and letters you gave me have to do with the testing that the lights have undergone as opposed to a part number. Let me know what measurements you find!

view full answer...

Answer 10

The Tekonsha OEM Replacement Vehicle Wiring Harness part #TK22115 is a great option for a 2017 Mercedes-Benz Sprinter 2500. It as you noted has a 7-way plug but there isn't a complete harness with both 4 and 7-way plugs as is. Therefore, I…

view full answer...

Answer 11

We know that the Fulton Fender part #F008583 that you referenced will easily fit on a Shoreland'r trailer that has tandem axles but it is not a direct bolt-on application. Some small modifications will need to be made. Check out the review I…

view full answer...

Answer 12

The correct replacement lens for the RV Driver Side Tail Light part #RVST61 on your Forest Rive trailer is the Replacement Lens part #AST61B. This light has the clear portion at the bottom to allow the licence plate bulb to show though.

view full answer...

Distance from Center of Pin Hole to End of Receiver on Curt Combo Bar E-9

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching