Compatibility of Equal-I-zer Bracket Jackets with Fastway E2 Trunnion Weight Distribution System

Question

Question:

Are these pads compatible with Fastaway e2 94-00-1000 trunnion?

asked by: Scott B

0

Expert Reply:

The Equal-I-zer bracket jackets you referred to, part # EQ95-01-5150 will work with your Fastway E2 # FA92-00-1000 weight distribution system. However, if you use the bracket jackets, you'll reduce the effectiveness of the sway control feature that the E2 provides. The jackets will prevent the metal on metal friction between the spring bar and the L bracket attached to the trailer frame.

expert reply by: Mike L

0

Answer 1

Hi Greg! There isn't a preferred or specific ball mount for the Oris Disappearing Hitch Receiver #TS49VR as it will always sit a bit different depending on the vehicle. With it being very recessed on your Mach-E, you will just need to find one…

view full answer...

Answer 2

Cheryl, each Transformer dolly #PA66VR includes two 12-volt Interstate U1 deep-cycle batteries wired in parallel (12V, 2x the amperage). You’ll typically get around 30–40 minutes of continuous operation on a full charge - more than enough to maneuver…

view full answer...

Answer 3

Hi Norm; the B&W Digital Tongue Weight Scale #BW34KR is designed for bumper pull trailers only. The coupler will fit onto the scale to measure tongue weight. There is no way to safely hook up a 5th wheel or gooseneck to the scale and measure. The…

view full answer...

Answer 4

Yes, the round bar Fastway e2 weight distribution hitch is compatible with the Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems #EQ95-01-5150.

view full answer...

Answer 5

The Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems part #EQ95-01-5150 are compatible with the Fastway e2 Weight Distribution w/ 2-Point Sway Control part #FA94-00-1000. They will slightly diminish the sway control feature because…

view full answer...

Answer 6

Hello Miles, thanks for reaching out. The Sway Bracket Jackets #EQ95-01-5150 can help to reduce the road noise created by your E2 round bar hitch. The only downside to the jackets is they can reduce the effectiveness of your WD hitch. They will help…

view full answer...

Answer 7

Yes, the Equal-i-zer Sway Bracket Jackets #EQ95-01-5150 can be used with your Fasteway E2 Weight Distribution Hitch

view full answer...

Answer 8

The easiest way to disable the Continuous Damping Control Suspension (CDC) on your 2011 GMC Yukon XL Denali is to pull the " Electronic Stability Suspension Control, Automatic Level Control Exhaust" fuse which is located in the #2 position…

view full answer...

Answer 9

When using a weight distribution system on a vehicle that has self-leveling suspension like your 2018 Dodge Durango the trick is to set the tongue weight on the hitch ball so that the suspension works to level the vehicle and then go ahead and setup…

view full answer...

Answer 10

To set up a weight distribution system with your Jeep you will want to first disable the quadra lift system and setup the weight distribution system without it. To do this you will use the spare tire changing setting. To assist with changing a spare…

view full answer...

Answer 11

For vehicles with auto-leveling suspension the proper setup procedure for weight distribution is to put the full tongue weight on the trailer hitch to activate the vehicle's auto-level function and then from there go through the setup procedure…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Compatibility of Equal-I-zer Bracket Jackets with Fastway E2 Trunnion Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching