How to Determine if the Fulton XLT Will Bolt Up to a Welded on Trailer Bracket on Boat Trailer

Question

Question:

I have a worn out Fulton trailer jack to replace on a boat trailer. It came with a welded on bracket that the jack bolts to. Will the Fulton XLT Swivel Trailer Jack - Bolt On - Sidewind - Single Wheel - 12inch Lift - 1,500 lbs bolt onto the existing common Fulton bracket? Im also trying to figure out if this jack gives me more total lift possibility than the F2 series? Its hard to tell as the F2 has an 8inch slide adjustment built in.

asked by: Mike

0

Expert Reply:

Does the welded on bracket on your trailer look like the part # P9012-00? If so, then you would want the part # F141132 for a Fulton XLT jack that would bolt right up to your trailer.

If not, then you could pretty easily remove the bracket and install the # P9012-00.

expert reply by: Jameson C

0

Answer 1

Hello Jim, The Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K #FTJ120W0301 is rated for 1,200 pounds. Keep in mind that this rating applies to the tongue weight of the trailer, not the overall trailer weight. For…

view full answer...

Answer 2

Hey Robert, so the big difference between the two jacks is the frame dimensions they are designed to fit. The part #F1413040134 is for 3 inch by 4 inch whereas the #F1413140334 can fit frames that are up to 5 inches tall so it really comes down to…

view full answer...

Answer 3

The Mounting Kit #MJ-1000B-MK is a replacement part for the Round Swivel Marine Jacks #MJ-1200B and #MJ-1500B which actually mounts to the side of the frame of your trailer instead of in the hole location in your A-Frame coupler area. As long as your…

view full answer...

Answer 4

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 5

It sounds like you are actually needing the Replacement Hardware Kit for Fulton Swivel Jacks #F0933325S00.This fits a mounting plate like the #P9012-00 that it sounds like you have welded to your trailer. It includes the metal bushing/washer that you…

view full answer...

Answer 6

Yes, the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141132 that you referenced is designed to fit the same style of mounting bracket that you have in the picture you submitted. This jack will bolt right up.

view full answer...

Answer 7

The Fulton Bolt-Thru Swivel Marine Jack #FXP15W is a bolt through replacement option for you. This is designed to use a welded plate like the Jack Mounting Bracket for Fulton Marine Jack #P9012-00. It appears like you have a bolt that goes into a…

view full answer...

Answer 8

The closest option we have is the Fulton F2 Swing-Up Jack w/ Pivoting Footplate - 4"-5" Frames, Sidewind, Bolt On - 2,000 lb #F1413230134 which has a bolt on mount that fits 4" to 5" frames, and has a foot plate like you were…

view full answer...

Answer 9

Without knowing the part number and manufacturer of your current trailer jack, I couldn't speak to the compatibility of the mounting plate for your current jack with the mount that the Fulton #F141132 XLT uses. The #P9012-00 weld-on mount for the…

view full answer...

Answer 10

Hi Jared, You can upgrade from the Fulton #FTJ120W0301, and while you mentioned options for an upgrade, there really is just one that is going to work with your bracket, which is the jack you mentioned, the Fulton XLT Boat Trailer Jack #F141132. This…

view full answer...

Answer 11

We don't have the dimensions of the weld-on mount for your Shelby jack, but it looks similar to the Jack Mounting Bracket for Fulton Marine Jack - Weld-On #P9012-00. That mounting bracket uses a 1/2" bolt with pin holes measuring 3"…

view full answer...

Answer 12

The Fulton jack part #F141132 that you referenced is a really great jack that I know you'll be happy with, but it requires the bracket part #P9012-00 to mount to a trailer which isn't the same as what you have now. So your best option is to…

view full answer...

How to Determine if the Fulton XLT Will Bolt Up to a Welded on Trailer Bracket on Boat Trailer

Featured Help Information

Miscellaneous Media

Continue Researching