How to Connect Trailer Wiring to Optronics # ST8RB and # ST9RB Trailer Tailllights
Updated 03/26/2016 | Published 03/24/2016
Products Featured in This Question
Question:
I have all new equipment from you to rebuild my trailer but I do not have the Connectors for the lights. Didnt see it with the items and cant find it now. I have the ST_9RB tail lights and just need the electrical connectors or harness that has the proper connectors. Thanks
asked by: Dan H
Helpful Expert Reply:
If you have the Optronics # ST8RB and # ST9RB, no connector is needed. On the back of the taillight, there is a hole for the stop/turn and a hole for the running light wire. Each of these holes will have a smaller hole directly below it. Strip back the insulation on the wire by about a 1/4 inch, twist the copper strands of each wire tightly and push it into the hole in the back of the lamp as you're pushing a small screwdriver into the smaller hole. Once the wire is fully inserted, remove the screwdriver, which locks the wire into place. The two mounting bolts provide the ground connection, so the lamp will need to be connected to the metal trailer frame, or to a piece of metal that's connected to the trailer frame.
If you click the video link I've provided for you, it'll be clear to you.
Product Page this Question was Asked From
Optronics Combination Trailer Tail Light - 6 Function - Incandescent - Red Lens - Passenger Side
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- Marker
- Square
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 5-5/16L x 4-9/16W Inch
- Red
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Truck Bed Camera
- Shop: Combination Trailer Tail Light - 7 Function - Incandescent - Square - Red Lens - Driver Side
- Q&A: Troubleshooting Right Tail Light on Trailer that Stays On with Vehicle Ignition Off
- Shop: Optronics Combination Trailer Tail Light - 6 Function - Incandescent - Red Lens - Passenger Side
- Q&A: Where Does Red Wire of 4-Way # 62990 Wire To on Trailer
- Q&A: Right Turn Signal/Brake Light Stays On with Curt Trailer Wiring Harness on a 2016 Toyota Tacoma
- Q&A: Can I Upgrade From 175/80-13 Tire to 185/80-13 Tire
- Q&A: Replacement Rear Taillights and Clearance Light Bar for Boat Trailer
- Q&A: Recommended Wiring and Lights for Utility Trailer
- Shop: LED Trailer Combination Tail Light - Submersible - 7 Function - 10 Diodes - Red Lens - Driver Side
- Video: Fishing Rod Holder: The Breakdown
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Shop: Fishing Rod Holder - Horizontal Clamp On - 6" Circumference Rails
- Video: Detailed Breakdown of the 35 Ft 4-Way Trailer Wiring Harness
- Video: What to Know About the 25 Ft 5-Way Trailer Wiring Harness
- Video: A Closer Look at the Quick Splices
- Search Results: wire connectors wiring
- Video: All You Need to Know About the Combination Trailer Tail Light
- Shop: 25 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 25' Ground
- Search Results: rear light bar
- Search Results: wire clips
- Search Results: rear trailer lights
- Search Results: electrical tape wiring
- Search Results: trailer lights
- Q&A: What is Most Common Trailer Wheel 6 Lug Bolt Pattern
- Video: Optronics Combination Trailer Tail Light Review
- Video: An In-Depth Look at the Peterson Tail Light for Trailers Over 80" Wide
- Article: Trailer Wiring Diagrams
on Trailer Lights
