Prodigy P3 # 90195 Brake Controller Installation in 2014 Honda Odyssey

Question

Question:

Hello, Im looking to buy the Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional for my 2014 Honda Odyssey. Is there an under dash connector in the 2014 Honda Odyssey for this controller or would that be part of the install process? Thanks!

asked by: Megan B

0

Expert Reply:

Honda didn't provide a brake controller connector in the 2014 Odyssey, but have no fear, the installation is pretty straightforward, as you'll see in the installation video and installation instructions I've linked for you.

In addition to the Prodigy P3 brake controller, part # 90195, you'll also need the brake controller installation kit, part # ETBC7 and a 4-pole trailer connector, # 118521 unless your Odyssey already has one.

The video shows the install kit being used to install a different brake controller in a 2014 Odyssey. The procedure for your installation will be exactly the same.

expert reply by: Mike L

0

Answer 1

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 2

The difference between the plate and fin style, #D13504, and the tube and fin style cooler, #D12904, is that the plate and fin models can cool better than the tube and fin models. You will notice that plate and fin coolers with the same rating as…

view full answer...

Answer 3

For your Sienna, given your location and the fact that you describe your planned towing activity to be moderate, I'd recommend a middle of the road option, the Derale #D13501. The cooler is large enough to be effective for moderate towing, but…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Prodigy P3 # 90195 Brake Controller Installation in 2014 Honda Odyssey

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching