How Far Does the Suspension Travel on the Timbren A35RD545E

Question

Question:

I am building a trailer with the Timbren 1200lb axle less trailer suspension and need to know what the vertical travel of the timbren is ? So i know how much clearance to leave over my tire? Please let me know what the travel is ? Thanks

asked by: Andy

0

Expert Reply:

The deflection (or amount the suspension can travel), for the Timbren part # A35RD545E that you referenced is 1-3/4 inches.

I attached a picture that shows this dimension as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Timbren systems that include brakes do not have parking brakes. The electric drum brakes included are Axletek. The 6 inch measurement from the hub face to the hangers of the system is accurate for the #A35RD545E system you're looking at.

view full answer...

Answer 2

We do have engineering diagrams for the Timbren Axle-Less Trailer Suspension System #A35RD545E that you referenced, and we do show these on our product page. If you scroll down a bit you'll find several measured drawings of this system with…

view full answer...

Answer 3

We have the Timbren Axle-Less Trailer Suspension System #A35RD545E you can use to replace your current axle. We do not currently carry a traditional axle that matches your dimensions and one would have to be custom made. This system includes all new…

view full answer...

Answer 4

I have attached a top view photo with additional dimensions that should be helpful. As you may already know, this system will have 1-3/4 inches of deflection under a full load. If you are using fenders, I recommend placing the fenders 3 inches above…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How Far Does the Suspension Travel on the Timbren A35RD545E

Product Page this Question was Asked From

Continue Researching