Plastic Fender Recommendation for Shorelander Trailer with 14 inch Wheels

Question

Question:

I have a 1993 Shorelander single axle trailer with 14foot tires that needs a new plastic white fender. The mounting brackets are 31.25inch apart. what do you reccomend?

asked by: Ron R

0

Expert Reply:

It looks like the closest fender we have that should work well would be the part # F008574. If you check out the dimension picture that I attached you will see that the mounting bracket dimensions for this fender should match up well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

There is a slight difference in the designs of the Fulton fender #F008584 and the CE Smith Fender #CE19504 but other than appearance there isn't a whole lot of difference. I have stood on a Fulton fender before and it did flex but it didn't…

view full answer...

Answer 2

We do offer trailer fender mounting brackets and these are general-application types; they are not specific to a particular fender type or design, nor are they specific to any one type of trailer. Karavan currently offers over 50 different boat…

view full answer...

Answer 3

Thanks for the picture! I have something close to your 26" slipper springs. It is possible to switch to a two eye leaf spring or even go down to a four leaf spring with a higher capacity. If you wanted to switch it up to a two eye leaf spring I…

view full answer...

Answer 4

The Fulton Single Axle Trailer Fender part #F008573 should fit your Shorelandr trailer, but it does not come with lights. For the Fulton plastic fenders we recommend the Left Fender Clearance Trailer Light #BA44FNL and the Right Fender Clearance…

view full answer...

Answer 5

The side and/or VIN of the trailer is not required. The Fulton fender #F008574 can be fitted on either side of the trailer. And since it is a universal application it does not matter what the trailer make and model is. What does matter are the fender…

view full answer...

Answer 6

The closest white plastic fender we carry that is designed to bracket-mount to the M1 measurement you are looking for is the part #F008574 which has a M1 measurement of 30-1/4 inches. This fender is sold individually. I attached a picture that has…

view full answer...

Answer 7

The most important measurement is the mounting bracket slots and the Fulton Single Axle Trailer Fenders with Top and Side Steps #F008574-2 fit 14 inch wheels and measures 30-1/4 inches from inside to inside for the mounting brackets, which do not…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Plastic Fender Recommendation for Shorelander Trailer with 14 inch Wheels

Featured Help Information

Miscellaneous Media

Continue Researching