Trailer Fender Mounting Brackets for Use with Fulton Single Axle Trailer Fender # F008574

Question

Question:

need the trailer fender mounting bracket i have a 2002 karavan boat trailer 43inch fender

asked by: Lionel H

0

Expert Reply:

We do offer trailer fender mounting brackets and these are general-application types; they are not specific to a particular fender type or design, nor are they specific to any one type of trailer. Karavan currently offers over 50 different boat trailers. For typical use with 8 - 12-inch wheels we offer bracket set # CE26061G-2; for 13 - 15-inch wheels we have # CE26098G-2.

Finding the right ones for your application will be easiest by using the search phrase 'fender mounting bracket' in our search box; this will let you see all options.

expert reply by: Adam R

0

Paul E.

7/1/2020

I’m looking at getting Fulton fenders. Will bracket CE26098G-2 fit this fender?

Chris R.

7/7/2020

Yes, the CE Smith Bracket Kit # CE26098G-2 will work really well with the Fulton fenders we have available.

Answer 1

It looks like the closest fender we have that should work well would be the part #F008574. If you check out the dimension picture that I attached you will see that the mounting bracket dimensions for this fender should match up well.

view full answer...

Answer 2

I was able to go out to the warehouse and measure the mounting brackets holes for the PF11X35W and found that it was 5-5/16 inches or 5.3125 inches. If these aren't an exact match, new holes can usually be drilled into the brackets to make them…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Trailer Fender Mounting Brackets for Use with Fulton Single Axle Trailer Fender # F008574

Products Featured in This Question

Continue Researching