How to Correct Flashing LED Trailer Lights Using Load Resistors

Question

Question:

Hello, We are having issues with our Land Rover Discovery 3. The problem is the led caravan lights keep flashing when attached to the vehicle. When we the right indicator, the left strobes too and visa versa. Please advise if you have an adaptor to fix this problem. Regards.

asked by: Ray O

0

Expert Reply:

High-efficiency LED type trailer lighting pulls much lower current than standard incandescent lights and sometimes this can cause odd behavior from the wiring harness when it cannot recognize the connected trailer.

There's a simple solution to this issue: installation of a load resistor at each affected LED light. Load resistors mimic the electrical signature of incandescent lights to let the trailer wiring work as intended.

If your trailer lights use a PL-3 type connector you can use Optronics part # ALEDRST2B. If you need to hard-wire the load resistors we offer a 2-pack of the ceramic type, part # DI34ZR.

expert reply by: Adam R

0

Answer 1

What you are experiencing is due to the fact that LED taillights only require a very small amount of amperage to illuminate. A tiny amount can cause them to illuminate. Trailer wring for the most part goes totally dead when the vehicle is off. But…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

How to Correct Flashing LED Trailer Lights Using Load Resistors

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching