Replacement Wheel Cylinders for Dexter Drum Brakes

Question

Question:

Will the 0977600 Titan Replacement Wheel Cylinder - 10, 12, 13inch Brakes - Right Hand fit 12inch dexter drum brakes? Also what is the Left Hand part #.

asked by: Paul

1

Helpful Expert Reply:

Good news I can help you find the right replacement wheel cylinder.

To determine the correct replacement wheel cylinder for your hydraulic trailer brake assemblies is determined by the brand and size of brake assembly that is on your trailer.

Sounds like your trailer has a Dexter drum brake assemblies with 12 inch diameter hydraulic brakes then the Redline Wheel Cylinder, # BP17-030 (left) and # BP17-020 (right), will be the correct parts.

If you happen to have Titan brake assemblies with 12 inch diameter hydraulic brakes, then you would need the Titan Uni-Servo Wheel Cylinder, item # T0977700 (left) and # T0977600 (right).

expert reply by: Jackie C

1

Answer 1

To go from hydraulic drum brakes to disc brakes you need to know your axle capacity as well as the bearing numbers. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able…

view full answer...

Answer 2

Based on images I could find it would appear the maximum internal diameter is 10.09. This information should be stamped on the drum itself. If you do not have any dimensions stamped on your drum they should not be turned and will just need to be…

view full answer...

Answer 3

The best way to find the correct replacement bearings is to get the numbers stamped onto the metal of the inner and outer bearings that are currently on the trailer. If you cannot read those numbers your other option is to measure the spindle of your…

view full answer...

Answer 4

Thanks for reaching out, Ron! To replace the grease seal on your Dexter Trailer Hub & Drum Assembly #84546UC3-EZ (Dexter part K08-247-94) you can either get part #58846 for a single seal or part #RG06-050 for a set of seals. If you've…

view full answer...

Answer 5

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 6

First, lets start with master cylinder replacement. The recommendation you got for replacing the complete actuator, is most likely a good idea because there is a reason for the crud and such that you are finding in the master cylinder and replacing…

view full answer...

Answer 7

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Wheel Cylinders for Dexter Drum Brakes

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching