Spare Tire Carrier for RV That Pivots to Ground for Easy Installing/Removing Wheel
Updated 11/07/2015 | Published 11/06/2015 >
Question:
Have a 5th wheel with the spare tire mounted to the rear bumper. Problem is at 73 years old it now is a little hard to get the tire both off the back on the tire rack. I have seen what reminds of a small davit, that mounted to the back bumper and you could swing it out, attach the tire to the cable, and lift the tire either up or down. It mounted with 4 bolts and once you finished using it you disconnected it and stowed. Question: do you have something along this line? If not any ideas? Would it be possible to install an under camper crank down spare tire holder. I have a 31.5ft KZ Durango 2500. Rear living space, mid entry. Thank you, Respectfully, Bill White
asked by: Bill W
Expert Reply:
The closest product we have to what you are looking for would be the Roadmaster Spare Tire carrier part # RM-195225. This carrier allows you to pivot the spare down to the ground when you are installing or removing it to make it a bit easier to manage. You would then be able to pivot the carrier back up when you are done installing/removing the spare.
I attached a review video for you to check out as well.
Product Page this Question was Asked From
Roadmaster Hitch Spare Tire Mount with 2" Receiver Opening - 2" Hitches
- Spare Tire Mount
- Hitch Mount
- Universal
- RV
- Standard Finish
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Video: Detailed Breakdown of the Buyers Products Bolt-On 2" Hitch Receiver Tube
- Shop: Front Mount Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Bumper Mounted Trailer Hitch Recommendation for 2 inch Bumper
- Q&A: How To Mount Spare Tire And Bike Rack On RV
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Buyers Products Bolt-On 2" Hitch Receiver Tube - 20K
- Shop: etrailer Spare Tire Mount for Trailer with Angle-Iron Railing - Clamp On
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Brake Controller
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Search Results: trailer jack
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Article: How to Choose the Right Trailer Hitch Class


