I-Beam Clamps for Post Style Guide-Ons for a Boat Trailer

Question

Question:

Do you sell just the guide post clamps?

asked by: Dave

0

Expert Reply:

Yes, the I-Beam frame clamps that come with guide-ons # CE27635 are available separately. For one clamp you would need # CE27681G. They secure a 1-1/2 inch square tube to an I-Beam and 4 are needed per I-Beam. Or you could use # CE27682A for 2 sets. They fit I-Beams with width of 2-1/2 inches to 4-1/2 inches.

expert reply by: Michael H

0

Answer 1

Hey Tom, thanks for reaching out, and good question, and this one’s actually simpler than it looks once you see how CE Smith sets these up. The CE Smith I-Beam Clamp #CE27681G is designed around 3/8" hardware, not anything bigger. The clamp…

view full answer...

Answer 2

Hey Mike, The metal post on the guide-ons #CE27635 are going to be 38" long, from the notch that the PVC pipe sits on to the bottom it is 11.8". The metal post goes up 27" total into the PVC pipe. What kind of trailer are you wanting…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

I-Beam Clamps for Post Style Guide-Ons for a Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching