Hardware Needed To Install 36 Inch Lock Side-Door Bar Lock Assembly

Question

Question:

what is part number for hardware to install 36inch Lock Side Door Bar Lock Assembly?

asked by: Bill G

0

Expert Reply:

To install the 36 Inch Lock Side-Door Bar Lock Assembly # 305736 you will want to use carriage bolts, nuts, and washers. There is not a part number that includes this hardware for # 305736.

You will want to use 5/16 inch carriage bolts to secure the latch to the trailer. You can find these carriage bolts at your local hardware store.

expert reply by: Victoria B

0

Answer 1

If you want an entire replacement latch assembly you could use the #305736 you were looking at. I can't quite tell from the picture but it looks like that is the old pipe and what you really need is a handle to attach. The #158-100 could be…

view full answer...

Answer 2

The #BLTL-23 Blaylock coupler lock is compatible with a very specific type of coupler, the CollarLok like our part #BD028499, so it wouldn't be a good fit for a coupler like the Demco #DM14040-81. A lock like the #FA86-0015-316 or a latch type…

view full answer...

Answer 3

If you have the new style Demco eZ-Latch coupler I recommend using the Lock #IR66FR. Otherwise you will be able to use the Lock #2847DAT to secure the coupler latch. Both of these latches are constructed of stainless steel so they are okay to be…

view full answer...

Answer 4

Yes, you can so long as your Demco EZ latch coupler is cast like item #DM14040-81 or item #DM37ZR. The InfiniteRule Lock for Demco eZ-Latch Trailer Couplers item #IR66FR works great with these couplers whether they're being towed or parked.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Hardware Needed To Install 36 Inch Lock Side-Door Bar Lock Assembly

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching