Troubleshooting Trailer Turn Signals that Operate Backwards
Published 10/02/2015
Products Featured in This Question
Question:
I do have a problem. When I hooked up my camper trailer this summer. This was the first time I used the wiring harness. I find out when I use my right turn directional the left trailer light goes on. And vice versa? I looked if I crossed the wires, but it has to go that way because one wire is longer to reach to the driver side in the back. Do I have to add more wire to switch this?
asked by: Jack
Expert Reply:
It sounds like you may have installed the connectors of your trailer wiring on the wrong sides of the vehicle, or your trailer is wired backwards.
First thing you should do at this point is test the 4-way of the wiring harness with a circuit tester part # PTW2993 for voltage on all of the right pins when the taillight signals are being applied. Just like in the video I attached.
The yellow wire of the 4-way should be carrying the left turn/stop signal and the green wire should be carrying the right turn/stop signal. If this is correct then you should check your trailer's wiring for backwards wiring and fix as necessary.
If the problem is on the vehicle a very easy fix would be to cut the yellow and green wires leaving enough room to reconnect them and then swap the two wires. So you would run the yellow to the green and the green to the yellow. That would reverse the circuits without forcing you to completely reinstall the trailer wiring.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Powered Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Hidden
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: What is Difference Between Curt and Draw Tite Hitches for 2021 Lexus RX 450h
- Shop: Trailer Wiring
- Q&A: Trailer Turn Signals Blink Opposite of What they are Supposed To
- Video: Best 2017 Lexus RX 350 Trailer Wiring Options
- Article: Trailer Wiring Diagrams
- Shop: Vehicle Tow Bar Wiring
- Q&A: Turn Signals Reversed On Trailer Only When Running Lights Are On
- Shop: Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 12-1/4" Long - 7,500 lbs
- Shop: Curt Class III Drawbar - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Shop: Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
- Shop: Hook Probe Circuit Tester
- Shop: Brake Controller
- Video: All You Need to Know About the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches
- Video: Let’s Check Out the ShockStrap Ratchet Tie-Down Strap w Shock Absorber
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2021 Jeep Grand Cherokee L
- Q&A: What are the Different Circuits on a 4-Way
- Search Results: motorcycle tie down straps
- Search Results: safety chain carabiner
- Shop: Curt LED 4-Way Flat Connector (Vehicle End) Tester
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: tester
- Search Results: curt t~connector vehicle wiring harness with 4~pole flat trailer conne
- Video: How to Install the Curt Trailer Hitch Receiver on a 2022 Jeep Grand Cherokee WL - new body
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Search Results: curt mounting bracket
- Shop: Base Plate for Tow Bar
- Shop: Jeep Doors
- Article: How to Measure for Trailer Hitch Drop
on Custom Fit Vehicle Wiring
