Sidewinder Recommendation for Venture Pin Box CJ20517

Question

Question:

I need to know what sidewinder pin box will fit my camper with a venture pn cj 205 13

asked by: Josh S

0

Expert Reply:

I believe I have a solution for you, but the number you listed is one digit off of what is a standard pin box. You said you have a CJ20513 pin box which I was not able to find any record of this pin box. However, if you actually have a CJ20517 the correct Sidewinder you would need is the part # RP61450. I would recommend you confirm the model number of your pin box.

expert reply by: Jameson C

0

Answer 1

The 5th Airborne Premium w/ Sidewinder #RP61412 is the correct replacement for your Lippert 1716 pin box. Pin Box is #RP61412. This will move the pivot point 22 inches toward the rear of your truck, eliminating any concerns for cab interference with…

view full answer...

Answer 2

The correct Sidewinder for a CJ 20517 would be the part number #RP61450.

view full answer...

Answer 3

Thanks for reaching out and providing a photo, Greg! I reached out to my contacts at Dexter Axle and they weren't able to locate any information on this pin box and what could replace it. Since this is the case, I'll need you to check out the…

view full answer...

Answer 4

The number you found on the side of your current king pin will mean you have a Venture CJ20517. This does complicate things a bit as this style is not very common and the only option we have that will fit it is the Lippert Trailair Air Ride…

view full answer...

Answer 5

If you are unable to contact your trailer's manufacturer with your VIN to find the factory pin box model number there are some steps you can take which will allow you to determine what pin box model you have so you can purchase a new FlexAir. To…

view full answer...

Answer 6

Hey Maggie, thanks for reaching out. You’re right to double-check those measurements before ordering anything. The Lippert part #LC36VR is the one most folks end up using on Thor models with system number 0238222, but if your cylinder measures closer…

view full answer...

Answer 7

Hello Pat. We actually used to sell an angled brace from Lippert but it has been discontinued for quite some time. We do not carry one at this time but it was literally just a piece of angled steel. It might not be too hard to make one or find a…

view full answer...

Answer 8

With square axles, neither of our over/under kits will be a fit to raise the height of the trailer so another option is to use longer hangers for the leaf springs. You will just want to confirm the hangar height. You may be able to use a hanger like…

view full answer...

Answer 9

Hey David welcome back! I am not sure what you mean by angled pieces that get welded to the hanger. We have two types of X-Factor Crossmembers and one of them attaches directly to your frame hangers with included brackets and hardware. The MORryde…

view full answer...

Answer 10

You can lift your 2009 Mobile Suites 5th Wheel trailer, but since you have 8000-lbs Dexter Axles that are 3-1/2" diameter, the Dexter Trailer Springs Over-Under Conversion Kit #K71-385-00 will not work since they are only designed for 3"…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Sidewinder Recommendation for Venture Pin Box CJ20517

Continue Researching