Trailer Hitch Recommendation for a 2013 Volkswagen Passat TDI

Question

Question:

I have a 2013 tdi passat se with manual transmission. Will this hitch fit my car?

asked by: Phil R

0

Expert Reply:

The Curt hitch part # C11234 that you referenced has been confirmed as a fit for the TDI models of the 2013 Volkswagen Passat and does not have any exclusions for manual transmission models so it would work well for you. I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

For trailer wiring confirmed as a custom fit for your 2013 Volkswagen Passat the Curt T-Connector part #C56374 would be your best option. The #119250KIT is a hardwire kit that requires you to test circuits of your vehicle's taillights. The tester…

view full answer...

Answer 2

I recommend installing a trailer hitch like part #24880 on your Passat, and using a motorcycle trailer to carry your bike. None of the trailer hitches we offer are capable of handling a 550 lb motorcycle in a carrier. The trailer hitches we offer are…

view full answer...

Answer 3

For your 2013 Volkswagen Passat Diesel I recommend the Draw-Tite Sportframe Trailer Hitch Receiver #24880. This is a Class I hitch with 2,000 pound maximum towing capacity and 200 pound maximum tongue weight. It has the same capacities as the Curt…

view full answer...

Answer 4

Hey Anthony, looks like your 13' Passat is rated for towing up to a 1,000 lb trailer. Sounds like what you mentioned would fall under that number. Anything lighter than 1,000 lbs would be fine regardless of size. This would work great with the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Trailer Hitch Recommendation for a 2013 Volkswagen Passat TDI

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching