Replacement Hardware Kit Recommendation for a Curt Hitch

Question

Question:

I removed the hitch when the car was beyond repair and have acquired another Prism, 1999. Though in the meantime the bolts have been misplaced. Is it possible to order a replacement bolt kit from you? Thanks,

asked by: Herb W

1

Helpful Expert Reply:

To order replacement hardware for the Curt hitch part # C11181 all you need is the part # RHK. On the product page you will need to enter the part number for the hitch and select Curt from the drop down menu and we will ship you out the correct install hardware.

expert reply by: Jameson C

1

Answer 1

Hey Don. I have a solution for you, but that part is not available anywhere as far as I can tell. The only custom fit part our vendors offer as replacement is the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C55316…

view full answer...

Answer 2

The Replacement Hardware Kit #RHK is going to have the correct mounting hardware for whichever Curt, Da'Lan, Draw-Tite, etrailer, Hidden Hitch or Reese trailer hitch receiver you need it for. This is the reason for the Hitch Item Number box so we…

view full answer...

Answer 3

I attached a 7-way diagram that you can use as a wiring guide for installing the 7-Way kit part #PK11-934 that you referenced. You'd want to use the middle picture's wiring colors.

view full answer...

Answer 4

The Fastener Kit #01685 that you referenced is a supplement to the installation hardware included with the Draw-Tite Max-E-Loader Trailer Hitch Receiver #41504, or the Reese 37081 or 44143 hitches. This fastener kit is more or less spacers and you…

view full answer...

Answer 5

Drilling is required to install Draw-Tite trailer hitch #DT45502 on a 1988 Ford F-250. You will need to drill eight 1/2 inch holes to secure the hitch to the bottom of the vehicle frame. I have included a link to the installation instructions for…

view full answer...

Answer 6

Shane, sorry to say we don't have a replacement hardware kit by itself for the B&W Turnoverball #BWGNRK1313. The hardware actually does not look like it's offered by B&W themselves, unfortunately. What I did instead is attach a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Replacement Hardware Kit Recommendation for a Curt Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching