Length of Horizontal Part of Guide-On Bracket for CE Smith Bunk Style Guide-Ons

Question

Question:

Assuming a 2inch wide trailer frame and also assuming that the tubing is adjusted so that the horizontal distance of the tubing on the outside of the trailer frame is minimum, what would be the length of the tubing on the inside of the trailer frame? Also, what is the total length of the horizontal tubing? see attached pic I am concerned that when set to minimum horizontal distance, that my trailers bunk will be in the way of the inside section of tubing. Thank you!

asked by: Bob

0

Expert Reply:

I went out to the warehouse to measure the horizontal part of CE Smith Bunk-Style Guide-Ons # CE27660. The length is 12 inches so if 2 inches of frame are covering up part of that then that leaves 10 inches that will stick in towards the center of the trailer.

expert reply by: Michael H

0

Answer 1

I don't have any specifics on your boat or trailer but the main thing you need to check before using the CE Smith Bunkboard Guide-On Kit part #CE27600K75 is your frame size. This kit works with trailer frames 3" wide and up to 4-1/2"…

view full answer...

Answer 2

The wood used for the bunk boards on the #CE27660 CE Smith Bunk-Style Guide-Ons for Boat Trailers is not pressure treated. CE Smith uses untreated southern yellow pine for their bunk boards. These also feature marine-grade carpeting to protect your…

view full answer...

Answer 3

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Length of Horizontal Part of Guide-On Bracket for CE Smith Bunk Style Guide-Ons

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching