Do Weight Distribution Systems Need Anti-Rattle Devices

Question

Question:

Can I use this device on weight distribution hitch? If not what can I use? 2013 F150 4dr short bed pulling a 30foot Keystone Passport approx. 6000lb, 650lb tongue weight with a Fastway E2 Round Bar hitch, 2-5/8inch ball.

asked by: Phill W

0

Expert Reply:

If your Weight Distribution System has been properly set up, there should be no movement of the weight distribution shank in the receiver, as the spring bars should be placing a substantial amount of tension on the shank against the walls of the receiver, thus keeping it firmly in place. The tension applied would be much greater than what a product like the Brophy Anti-Rattle would provide. If you are experiencing the rattle when using the weight distribution head to tow a different trailer and the spring bars are not being used, you would be best served by using a standard ball mount and trailer ball.

I would recommend reviewing the instructions that came with your Weight Distribution System to ensure that it is adjusted properly.

expert reply by: Jameson C

0

Answer 1

Good afternoon Stephany, I'm sorry you had that less-than-stellar experience with the pin style anti-rattle device. Normally that setup works pretty well, but in some extreme towing situations, I definitely think the clamp style is better at…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

Hey Braden, thanks for reaching out. Yes, we do have an anti-rattle device that will work great with your Blue Ox WD setup. The U-bolt style anti-rattle devices are going to give the best results, and for that I recommend the following: - Blue Ox…

view full answer...

Answer 4

Hey Jim, the Kodiak Disc Brake Caliper #KDBC225DAC is designed so that it can be used on either side of a trailer axle so there isn't a specific left and right. This also can be used to replace a Reliable CR1000 and CL1000 so it will work for you…

view full answer...

Answer 5

Hi Mike! The Blue Ox Avail Non-Binding Tow Bar - RV Mount - 2" Hitch - 10,000 lbs #BLU28QV is the new version of the Avail #BX7420. I wasn't sure what the difference was either, so I asked Blue Ox. They said the only difference between them…

view full answer...

Answer 6

Hey Richard. welcome back! The Go Power Pure Sine Wave Inverter Charger #GP75QR does not include the display. You will need the Go Power PowerTrak Screen #GP64XR to go with it. You will also need the #GP74XR, #GP84XR, and #GP24XR to make all of your…

view full answer...

Answer 7

Yes, I was able to verify with Curt their Front Mount Trailer Hitch Receiver #C31078 will fit your 2024 Ford F-250 4 wheel drive.

view full answer...

Answer 8

Hello James, Happy to confirm the parts for your 2025 Ford Bronco with factory plastic bumper that has tow hooks, but NO D-Rings. - Base Plate: Blue Ox Base Plate Kit - Removable Arms #BLU97XR since you do not have D-Rings this will work. - Tow Bar:…

view full answer...

Answer 9

Hey Eric! Yes, you can still use the Meyer WingMan Commercial-Grade Hydraulic Snowplow #ME55FR on your truck with a lift. What you need to do is measure the hitch height. Meyer requires 10"-13" from the ground to the centerline of your…

view full answer...

Answer 10

Hey Jim, thanks for the dimensions from both your trailer hitch on your Colorado and the coupler of your Scamp trailer. With that info what you need is a 1 inch rise from your ball mount with a 2 inch hitch ball. For that the Curt ball mount part…

view full answer...

Do Weight Distribution Systems Need Anti-Rattle Devices

Product Page this Question was Asked From

Continue Researching