Brake Controller Wiring Adapter to Install Reese Towpower Brakeman Controller on 2015 Ram

Question

Question:

I tried installing a Reese Towpower Brakeman Controller in my 2015 Ram, I connected it using the Tow Ready 20273 harness and it doesnt work. It seems that I loose the brake switch signal when the trailer is connected. After some reading on your site I see that the connector harness 3024-P is needed to work with the Tekonsha controllers. Would my current controller work if it were wired to the 3024-P harness with the included diode? Or do I need a new controller?

asked by: Michael

0

Expert Reply:

The # 20273 brake controller wiring adapter you referenced is compatible with the 2010-2012 Dodge Ram, but because it lacks the diode in the stop lamp switch circuit, it won't work on your truck.

You'll need the # 3024-P wiring adapter which is compatible with your Reese Brakeman brake controller. I've edited a photo for you showing where the connector is located under the dash.

expert reply by: Mike L

0

click to enlarge

Answer 1

You will need the Stop Light Switch Kit #RM-751449 for your 2019 Jeep Grand Cherokee. This will provide you with a brake signal as the factory brake switch wiring is very thin and not recommended for splicing into. This switch includes a custom fit…

view full answer...

Answer 2

Good question; so the issue with your 2019 Jeep Grand Cherokee is that it doesn't technically have a traditional stop light switch, which is why you are having trouble getting 12 volts. The good news is the Stay-IN-Play DUO Supplemental Braking…

view full answer...

Answer 3

When you are hardwiring a trailer brake controller like the Prodigy P2 #90885 the red wire connection that provides the triggering signal to the controller should be made to the wire on the COLD SIDE of the brake light switch circuit. This is the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Heidi. To use a Curt Echo Wireless Brake Controller item #C51180 on a tow vehicle with only a 4-way connector, you'll need the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation item #ETBC7L. The Curt Echo item #C51180 requires a…

view full answer...

Answer 11

That’s a great question Chadwick, and this is one of those situations where the change in technology really matters. The GE Appliances Low-Profile RV AC w/ Heat Pump part #GE26RR will replace your current ARC13AACBL2 setup, but it’s important to know…

view full answer...

Answer 12

The factory brake controller connector on your 2021 Jeep Grand Cherokee is located under the dash behind the hood latch, as shown in the provided photo. Keep in mind, the connector will only be there if the vehicle has the factory tow package which…

view full answer...

Brake Controller Wiring Adapter to Install Reese Towpower Brakeman Controller on 2015 Ram

Continue Researching