Dimensions Of Holes On Lippert 1621 5th Wheel Pin Box

Question

Question:

What are the size of the holes shown in the attached photo?

asked by: Bob

0

Expert Reply:

I went to our warehouse and measured the holes you mentioned you wanted the measurement for on the Lippert 1621 5th Wheel Pin Box, part # LC1387882.

The holes measure 3/8 inch diameter. I have also attached a drawing of this pin box with the dimensions shown from a side view.

expert reply by: Jeffrey L

0

click to enlarge

Neil C.

9/6/2020

What are the 3/8 holes for on the sloped face of 1621 pin box? Can they be filled in to eliminate water intrusion?

Jon G.

9/9/2020

Those 4 holes are there in case you'd like to add a cover like part # LC301458 to your pin box. If you don't want to add a cover then you can definitely plug them up because they don't serve for any other kind of function.

Neil C.

9/9/2020

@JonG Does the cover require screws into the RV or just the use of the 4 holes on the pin box? Thank you!

Jon G.

9/11/2020

@NeilC It looks like you use the 2 lower holes (I'm guessing the upper holes are for different other style covers out there) and then the top of the cover will fit on the underside of your 5th wheel camper.

Answer 1

Hey Todd, welcome back! The Curt Flex Air part #LC369535 that you referenced will be a great option for a cushioned pin box that will make a noticeable difference in ride quality. This does not sit 6 inches taller than your current Rota Flex so there…

view full answer...

Answer 2

Hey Matt, I was able to track down a set of install instructions for the PullRite SuperGlide Quick Connect Capture Plate for MORryde Cushioned Pin Boxes #PUL76RR that I saw you ordered in your order notes. I attached the pictures below this message…

view full answer...

Answer 3

Hey, James! Nice to see you again! The Gen-Y Hitch #GY76PR will not fit your 2013 Heartland Cyclone 3800. That model is designed for the Rhino bolt pattern, which did not start appearing on 5th wheels until around 2025. It’s very possible your…

view full answer...

Answer 4

Hey Jack, all of the fifth wheel pin box to gooseneck adapters like the MORryde Goosetech part #MR64MV all have right at the same dimensions from the gooseneck coupler to where it attaches to the trailer. There isn't one that offers more or less…

view full answer...

Answer 5

The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #GY68GR is roughly 2" shorter than the Lippert 1621 pin box. I've attached a dimensional drawing of #GY68GR for you to check out as well.

view full answer...

Answer 6

I have attached an image of the dimensional drawing for the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #GY68GR.

view full answer...

Answer 7

All axles, including the Trailer Axle with Idler Hubs #e25GR you referenced, are measured by capacity and two measurements (hub-face to hub-face & spring center to spring center). The hub-face to hub-face measurement ensures that your wheels will…

view full answer...

Answer 8

Hey Roger. In order to get you the correct Reese goosebox, I'll need the information on the sticker that's attached to your current pin box. The sticker should say date of manufacture, possibly weight capacity, and have some form of RPO, LCI,…

view full answer...

Answer 9

Hey Carl, thanks for the pics! You are correct the Shocker Hitch Quick Air Cushioned 5th-Wheel-to-Gooseneck Pin Box item #SHK47YR does have the built in chain attachment point. You can use the Reese Safety Chain Kit with Clevis Hooks item #RP49151.…

view full answer...

Answer 10

Hey Jeff! The MORryde GooseTech 5th Wheel to Gooseneck Pin Box #MR97MV comes with a Demco eZ-Latch. The best option for a lock is the InfiniteRule Lock for Cast Demco eZ-Latch Trailer Couplers #IR66FR. This is designed to for a standard coupler but…

view full answer...

Answer 11

Thank you for the information and photo! I was able to determine that you have a 1621 SHD (super heavy duty) pin box rated for 21K. The Gen-Y equivalent is found as part #GY68GR for a 4.5K tongue weight or part #GY46FR for a 5.5K tongue weight. While…

view full answer...

Answer 12

Manufacturers don't list the pin boxes they use so I don't know what your current pin box bolt pattern is in order to confirm the fitment of the MORryde Cushioned 5th Wheel Pin Box for 11.5K to 14K Trailers w/ Lippert 1621HD #MR74VR. On your…

view full answer...

Dimensions Of Holes On Lippert 1621 5th Wheel Pin Box

Product Page this Question was Asked From

Continue Researching