How to Install a Brake Controller in a 2013 Toyota Tundra with Factory 7-Way

Question

Question:

I have 2013 Toyota tundra and plan to purchase 39523 for 2 axle camper. Im not sure what I need to wire it. I have a factory plug near the parking break. Does this controller come with long enough wire to reach the console? Do I need an accessory cord? How do I know if the controller plug is the same as factory plug?

asked by: Adam

0

Expert Reply:

To install the Tekonsha PowerTrac Brake Controller part # 39523 in your 2013 Toyota Tundra with a factory 7-way all you need is the correct install harness, part # 3040-P. This plugs into the connector found near your parking brake.

To see how a similar controller would install in a 2013 Toyota Tundra like yours check out the install video I attached.

expert reply by: Jameson C

0

click to enlarge

Answer 1

In addition to the Curt trailer hitch #13198 for the 2009 Toyota Tundra (excluding TRD or Sport package), you will need a ball mount, ball, pin and clip, and a wiring harness if not already present on the truck. I recommend the etrailer ball mount…

view full answer...

Answer 2

The only Class V hitch offered for your 2012 Toyota Tundra is Curt model #C15398. Like many of the aftermarket hitches made for your Tundra this one fits only if there is no factory-installed hitch already taking up or blocking access to the mounting…

view full answer...

Answer 3

Yes, you can! We've spoken to Curt about this exact issue before and we do have a solution. The Curt Hitch item #C15398 is designed for the 2013 Toyota Tundra's that come without a factory hitch. However, it will fit the Tundra's that…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

How to Install a Brake Controller in a 2013 Toyota Tundra with Factory 7-Way

Featured Help Information

Miscellaneous Media

Continue Researching