Recommended Staple Size for Bunk Board Carpet

Question

Question:

What size staple is recommended for stapling bunk board carpet?

asked by: Mike

0

Expert Reply:

We typically try to use 1/2 inch stainless steel staples when we install the CE Smith Deluxe Marine-Grade Carpeting, # CE11372, but 3/8 inch staples will work too. I would not go much shorter than the 3/8 inch staples because you don't want them to work their way out over time. I strongly recommend using stainless steel staples if possible. They will last much longer because they provide the best rust resistance.

expert reply by: John H

0

Answer 1

We typically try to use 1/2 inch stainless steel staples when we install the CE Smith Deluxe Marine-Grade Carpeting, #CE11330, but 3/8 inch staples will work too. I would not go much shorter than the 3/8 inch staples because you don't want them…

view full answer...

Answer 2

Hey Lonnie, so we do offer a larger roll with part #CE11373 which is an 18' long 18" wide grey bunk carpet. If you are wanting to stick with the 11" wide carpet, I am afraid the 12' long roll #CE11372 is going to be the longest roll…

view full answer...

Answer 3

If you have an actuator like the Dexter #T4750620 you looked at, the only way to lockout the brakes is with the electric lockout. If you have a different model it is possible it has a spot for a key on the side like the #DX94FR which would work with…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You can pretty easily add an electric lockout to the Titan Model 10 actuator part #T2478100. For that all you would need is the part #T4748800. This will then allow you back up a hill without the brakes locking up.

view full answer...

Answer 6

I checked the instructions for the Demco Solenoid Kit #DM5404 and though it is a little vague, you will want to have the flared inlet attached to the actual brake line and the flat inlet attached to the #6 fitting (which then attaches to the master…

view full answer...

Answer 7

I spoke to my contact at Titan and he informed me that there really isn't a simple way to lock out the sliding portion of the Model 10 actuators. You would have to either weld the two portions of the actuator together or drill holes through them…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Recommended Staple Size for Bunk Board Carpet

Product Page this Question was Asked From

Continue Researching