How Does Curt Coupler Repair Kit # C25194 Assemble

Question

Question:

does the big spring go inside of the coupler?

asked by: Jerry

1

Helpful Expert Reply:

It certainly does. I've provided a diagram for a different coupler repair kit that will show you exactly how the latch assembles and what goes where.

The threaded bolt from the handle inserts into the coupler. From underneath, slide on the spring, the jaw and the square plate, followed by the tension spring and the lock nut.

expert reply by: Mike L

1

click to enlarge

Answer 1

To determine the correct safety chains for your Honda CR-V towing your Dilly boat trailer you will need to consider a few things. First if you are using a Breakaway Switch #HM20060 or have a Surge Actuator #DM62VR you will need to measure the length…

view full answer...

Answer 2

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 3

The rating listed for a single chain, like the Curt #C80031 at 5,000 pounds of capacity, will double when two are used. So the #C80031 used as a pair will mean you would have 10,000 pounds of capacity. With that said, I am not a huge fan of the…

view full answer...

Answer 4

Thank you for the photos! It looks like Marvel used to be associated with Atwood and they went out of business a while ago. We have some similar coupler styles but I'm not seeing that any of our repair kits having the same design as your coupler…

view full answer...

Answer 5

I went out to our warehouse to measure the opening in the link for you on the Curt Safety Chain with S-Hooks #C80031. The inner measurement is 0.52 inches at the weld and the links are 0.66 inches on the inside so your 1/2 inch bolt will fit. I…

view full answer...

Answer 6

Hey Tim, yes you are going to need to cut off the old chain or cut off the loop that is welded to the trailer frame so you can install a new 24 inch safety chain like the part #TCTSCG30-724-03x1. I would cut the chain though so that you can reuse the…

view full answer...

Answer 7

The bolt pattern used on the Bulldog Jack BD195318 is a little different than most, but I did include a diagram showing how it measures. The outer tube will measure 2-1/4" x 2-1/4" and the inner tube is 2" x 2" . From the bottom…

view full answer...

Answer 8

You will need to replace your entire coupler assembly as the Atwood coupler that you have is obsolete and they are not producing any parts for it. I recommend replacing it with the Demco A-Frame Trailer Coupler #DM14791-97. This coupler uses the same…

view full answer...

Answer 9

Safety chain extension links simply need to match the size and capacities of your current safety chains. For example, if your chains were 1/2" diameter with a 16,500 lbs break strength and 3,300 lb working load limit you would want the Threaded…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

How Does Curt Coupler Repair Kit # C25194 Assemble

Product Page this Question was Asked From

Continue Researching