Brake Controller Install on 2015 Toyota Highlander w/ Tow Package

Question

Question:

Hello, Just ordered a 2015 Highlander with factory tow package. Do you know if it has a plug under the dash to install a controller? Or do I need the ETBC7? Thanks

asked by: BC

0

Expert Reply:

According to my research, you can indeed install a brake controller on your vehicle, but the 2015 Toyota Highlander isn't equipped with the connector under the dash. You will need to use the # ETBC7 brake controller installation kit.

The kit contains everything needed to install a brake controller except for the controller and a functioning 4-pole trailer connector. If you don't have a functioning 4-pole, you can install one using part # 118449. For a brake controller, the Tekonsha Prodigy P2 you referred to, part # 90885 would be an outstanding choice.

I'll link you to instructions for the ETBC7, as well as some installation videos you'll find helpful. The brake controller install video shows a different controller being installed, but the procedure would be identical on your vehicle.

expert reply by: Mike L

0

Answer 1

Hey Jay, the correct replacement converter to replace what you have now that is compatible with LifePO4 batteries would be the part #PD69RR that you referenced. Progressive Dynamics likes to change their part numbers a lot and create revisions of…

view full answer...

Answer 2

We aren't able to source the sound bar you are looking for but it looks like it may be discontinued so you'd need to go with a different solution like the Furrion part #FSB2N25MCBL that you referenced. The wiring colors won't be an exact…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...