Correct Brake Controller Adapter for 2011 Ford F-150

Question

Question:

The brake unit I have is a Hopkins 47225 Brake-Force Brake Control. This is the unit I need the tow ready plug-in wiring adapter for ( 2011 ford f-150 4x4 crew cab). Could you please provide a part number if one is available?

asked by: Dwight

1

Helpful Expert Reply:

If you have one of the following brake controllers, we offer a complete plug-in application. No wiring needed, just plug one end of the Tow Ready Plug-In Wiring Adapter, # 22292, into your brake controller and the other end will plug into the built-in harness beneath the dash on your 2011 Ford F-150.

Brake EVN # TK63VR
Tekonsha PowerTrac # 39523
Tekonsha P2 # 90885
Tekonsha P3 # 90195
Tekonsha Primus IQ # TK90160
Tekonsha Voyager # 39510

If you have a different brand of brake controller, please send me an email with the name and model number and I would be happy to help you locate the correct wiring adapter.

expert reply by: Leah S

1

Dwight

12/22/2014

The brake unit I have is a Hopkins 47225 Brake-Force Brake Control. This is the unit I need the tow ready plug-in wiring adapter for ( 2011 ford f-150 4x4 crew cab). Could you please provide a part number if one is available?

Leah S.

12/23/2014

To install the Hopkins Brake-Force Brake Controller in your 2011 Ford F-150 you will need the Plug-In Simple Brake-Control Wiring Adapter, # HM47845. One end of the adapter plugs into your brake controller and the other end will plug into the built-in harness beneath the dash.

Answer 1

Brake controllers such as the Tekonsha Prodigy P2 #90885 and the P3 #90195 are not vehicle-specific so either will work fine in your 2011 Ford Expedition with factory 7-Way connector. Both will use the same wiring adapter #3035-P to connect to the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 8

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 9

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

Answer 12

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Correct Brake Controller Adapter for 2011 Ford F-150

Featured Help Information

Miscellaneous Media

Continue Researching