Replacement Retaining Clip Recommendation for Dexter 7 inch Brake Assembly Round Magnets

Question

Question:

Is there or isnt there a replacement part for these clips on the 7inch dexter brakes?

asked by: Dave B

0

Expert Reply:

I spoke with my contact at Redline about the availability of the retaining clip for the Dexter 7-inch brake magnets. He said you can use the Magnet Retainer Clip, part # BP19-001 , on the Dexter 7-inch round magnets. These retaining clips will work on both the 7-inch round and the 10-inch oval magnets.

expert reply by: Jameson C

0

Answer 1

The Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-468-469 does not come with drums, these will be purchased separately using the Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles part #84546UC3 or part #84546UC3-EZ for EZ-Lube.

view full answer...

Answer 2

Hey Steve, both of the kits you mentioned are self adjusting brake kits for 3,500 lb axles so they both will work. This part number is for a single axle though so if you have a tandem setup you'd need to order a quantity of two. The Dexter…

view full answer...

Answer 3

Regular "chatter" is not a common problem and since the magnet is damaged I strongly recommend replacing it with the Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies #AKBRKR-M7.

view full answer...

Answer 4

We do not have the exact magnet clip for 7 inch brakes so #AKBRKR-MC could work but it may need to be modified to fit. The other option is to replace the magnet which comes with a new spring and clip, #BP01-068. Without the clip the magnet can come…

view full answer...

Answer 5

The Dexter 7 inch electric brake assembly uses a magnet retaining clip that's different from the #BP19005 you described, which is only compatible with magnets for a 10, 12 and 12-1/4 inch brake assembly. The magnet retaining clips are indeed…

view full answer...

Answer 6

Coleman/Fleetwood uses Dexter axles so I can help you pick out the parts you need for your 2,200 lb Dexter axle. The bearings you would need are #L44649 for the inner and outer and then for a seal #10-9. For brake assemblies you would need part…

view full answer...

Answer 7

The 7 inch Dexter Brake Assemblies like the part #23-48 do use clips to attach the magnets to the assemblies. I went and pulled one from our warehouse and found that in order to attach the magnet to the arm you would need to slide the magnet over the…

view full answer...

Answer 8

You do not need to add additional grease to a Dexter trailer axle hub that came pre-greased. It has the correct amount in it and is ready to be used. Adding additional grease will most likely blow out the grease seal.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Retaining Clip Recommendation for Dexter 7 inch Brake Assembly Round Magnets

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching