Arrives before Christmas 
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Weld-on jack has a retracted height of 25-1/8" and an extended height of 40-1/4". Square design provides superior side-load support. Offers 15-1/8" of screw travel and 13-3/4" of drop leg travel. Includes a sidewind handle.
Features:
Specs:
Average Customer Rating: 4.8 out of 5 stars (829 Customer Reviews)
Weld-on jack has a retracted height of 25-1/8" and an extended height of 40-1/4". Square design provides superior side-load support. Offers 15-1/8" of screw travel and 13-3/4" of drop leg travel. Includes a sidewind handle.
It has been fantastic so far. I installed it as a replacement for the jack on the front of my 10k equipment trailer after the handle on the original jack broke off. I wish I had ripped the old jack off the day I bought the trailer and put this on in its place. MUCH MUCH MUCH easier to use, especially when the trailer is loaded.
I like the direct weld jacks. But I wish at least the outside tube was thicker with a little moe clearance with the inner tube. I put them on a 2020 Griffon 14’x7 ton dump trailer. I could not weld them directly to the trailer frame because I would not be able to crank the handles. I had to weld 1/2” x6” plates to the jacks to off set them farther from the fenders. I might use a little to much heat. Before I welded them the crank handles were very free. After welding they bind a little bit. But they still work great.
Makes a great stabilizer jack for my trailer when loading my tractor. Dont have to worry about putting wooden blocks under the back or have to carry any around anymore.
These jacks work great on our cable reel trailers we make here at Utiliquip. They weld on easily and can usually be repaired when someone drives away with the jack down or catches the handle on something and bends it. We use them as stabilizer jacks on our 14000lb GVWR trailer and they work gret!
No one can match your customer service.you have won me over . But you may want to get with your shipper about damage. The pictures are of the replacement damage box. But this time the part was not damaged.I will order from you in the future.
Charles N.
11/24/2023
Great product, no problems,Good quality
Nice looking jack made in America. It will slide inside the outer tube of the original Fulton jack and I can weld it on.
Prompt delivery and nice quality jack.
Brian
1/25/2024
The jack is still very solid after a year, cranking updown fine and not rusted up.
I bought two of these to weld onto the rear of my dump trailer to provide support when loading my skid steer. I added metal plates to extend the jack a little bit away from the wall of the dump trailer.
Will work as needed. Box was partially destroyed upon delivery.
Solid, well made. Easy installation. Works well on my home made log splitter.
Fast shipping item as described.
I have two of these on the back of my dump trailer for stabilizer legs when loading my skidsteer. Still working good after one year.
Joe
10/8/2021
Two years, no problems
I have replaced all of the crappy jacks on my 12 trailers at my ranch.
These drop leg jacks are so much more convenient and much stronger.
I am very happy with these jacks.
I always purchase jacks, hitches, lights, etc. from etrailer.
I ordered this jack on Tuesday and it arrived on Friday, I am in central Arizona, far from Phoenix.
The folks at etrailer ship fast and you can’t beat the prices or customer service.
Herald
I received my 2 7000 lb jacks, the packaging was destroyed and had been out in the rain, however they were in good condition with the exception of a couple dents in the top covers. They are well built jacks for the price. I was impressed that they have a grease fitting to keep it lubed up to prevent wear and make them easier to operate. I am using these jacks to build support jigs to split farm tractors for clutch replacements. I'm very satisfied with my purchase.
This is my fourth project using this jack over the past ten years. The retractable post and long reach provide lots of ground clearance. The weld-on square tube mount design makes it simple to configure to any orientation and height, and is more durable than any "swing-away" style jack can ever be. In ten years, I have "driven off with the plow down" several times and it does not bend. This jack is well worth the money and etrailer is a very reliable vendor. I will buy this again.
While this is a solicited review of this tongue jack, I am pleased to say the jack has met my expectations. It was an easy install in place of the OEM on 18 ft. Ringo flat bed. I will likely buy another for our cargo trailer which now has a bent non-drop leg due to pesky sidewalk humps.
I just received two of these jacks and had them welded on the rear of my flatbed trailer. They appear to be quality products and were relatively easy to weld on my trailer. I trailer a Kubota KX040 excavator, SVL 75 track loader and a TLB L45 backhoe and when loading each of these on my trailer, it raises the back end of my truck making it unsafe, until which point the equipment is situated properly on the trailer deck.
These are great jacks, I have been replacing all of the tongue jacks on my trailers with these. The drop leg foot is so handy, you don't have to crank on the jack forever.
I have bought several from etrailer and recommend them as the best place to get these, great price, fast delivery, great customer service.
Herald
These guys are absolutely the best we’ve found out there for any of our trailer part needs. Best prices always for quality products. Always prompt shipping.
They are our go to company. We always price check parts and strainer Always comes in with the best prices.
Great customer service and interaction with real people.
We are a U.S company that prefers both in sales and purchasing to support other U.S.companies. It’s just better when like etrailer, they kick the competitions *ss.
Great price , fast shipping and great jack....
just what I was looking for
Service and shipping 5 star, but for the product, works great, as described, BUT, I have to buy separate brackets to weld on, as the crank housing sticks out about 1/4”, and won’t sit flush against welding surface (dump trailer)
Work well and do as descpribed.
These worked great to support the tail of my trailer for loading equipment
well built i like the side crank much better than the top crank 3000 # lift that i currently have on my car trailer. i have a welder coming to install in next 2 weeks
Quick delivery and great product!
Do you have a question about this Trailer Jack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mark
10/14/2024
This jack was fantastic right up until it fell off the trailer last week not the jacks fault. It was WAY over kill for what I needed. I have the 3k version on hand now waiting to get installed. If I needed anywhere near 7k, Id get this jack again in a heartbeat.