Tube Dimensions Of The etrailer Square Direct Weld Jack w/ Footplate # TJD-8000S

Question

Question:

That is the size of the middle square tubing? Description states 2-1/4” outer tubing and 2” inner tubing, but there are three of them. Thank you

asked by: Benjamin F

0

Expert Reply:

The innermost tube of the Square Direct Weld Jack w/ Footplate # TJD-8000S is actually the drop leg and is less than 2". The black outer tubing is 2-1/4" and the aluminum inner tube is 2".

expert reply by: Kevin C

0

Answer 1

I do have option for you such as the Square Direct Weld Jack part #TJD-8000S which offers up to 28-7/8" of lift, 15-1/8" via the jack screw and the other 13-3/4" via the drop leg. This is a direct weld-on jack which offers up to a…

view full answer...

Answer 2

Hey Robert, thanks for the information. To add rear stabilizer jacks to your dump trailer, I recommend a pair of the Square Direct Weld Jack w/ Footplate item #TJD-8000S. This jack has a 7,000 lbs capacity and is sold individually so you'll need…

view full answer...

Answer 3

Thank you for the photos, they are appreciated, though unfortunately there are no crank handles I can confirm will fit your specific jack. The best option we have is a replacement jack for your trailer. There are budget-friendly options such as the…

view full answer...

Answer 4

The big difference is the orientation of the foot plate on both jacks. One just has the rectangular shaped foot plate rotated 90 degrees from the other. Aside from that they both have the same capacities and travel.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Tom, great question! Both products provide an easy way to measure tongue weight, but they excel in different situations. The BTBRV Trailer Jack Foot Scale #BTBRV014 measures tongue weight at the trailer jack, so you don't need to position a…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Tube Dimensions Of The etrailer Square Direct Weld Jack w/ Footplate # TJD-8000S

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching