Replacement Gear Kit for a 7K etrailer Square Direct Weld Jack

Question

Question:

Are the gears replaceable in this jack?

asked by: Kurt B

0

Expert Reply:

Yes, to replace the gears on the 7K etrailer Square Direct Weld Jack w/ Footplate # TJD-8000S you'll need the Replacement Gear Kit # TJD-7000S-GR.

Attached is a video showing how to replace gears for you to check out and use as a reference.

expert reply by: Jon G

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 6

I do have an option for you but we don't carry Vision LED so the only option we could offer is a full replacement like the Bright Way Push-to-Test Trailer Breakaway Kit part #3802346 which is a very comparable system. It has a side mount…

view full answer...

Answer 7

Super cab has a full size door and smaller rear opening door behind whereas the SuperCrew cab has 4 full size doors. I attached a picture that shows the two different styles. The part #25-0800 is designed to fit the crew cab models.

view full answer...

Answer 8

Hey Robert, thanks for the information. To add rear stabilizer jacks to your dump trailer, I recommend a pair of the Square Direct Weld Jack w/ Footplate item #TJD-8000S. This jack has a 7,000 lbs capacity and is sold individually so you'll need…

view full answer...

Answer 9

The closest jacks to the 8K Shelby 6108SW that we offer at this time are our Square Direct Weld Jack with Footplate, part #TJD-7000, and the 7.2K-rated Bulldog Square Jack #BD180354. For an 8K square side-wind jack we have Pro Series #PS1400860383.

view full answer...

Answer 10

The best solution we have is to replace the air brakes on your trailer with electric brakes. I understand this may not be ideal, but there is no kit that will allow you to use the air brakes with your brake controller. You will need several items to…

view full answer...

Answer 11

Hey Steve, yes the Dexter Nev-R-Adjust Brake Assembly set part #23-458-459 is the correct set for your Airstream based on the part numbers you mentioned. Also the hub/drum part #8-388-80UC3 that you referenced as well would be correct for your…

view full answer...

Replacement Gear Kit for a 7K etrailer Square Direct Weld Jack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching