Hello Steve, Welcome to etrailer, I'm glad you found us! You will need to add the Pollak Mounting Bracket #PK12711U separately. The etrailer Trailer Hitch Receiver #e98850 does not include the electrical connector or a mounting bracket for it. It…
Hello Joe, Thanks for writing in! Based on the measurements you provided, the Gen-Y Glyder Shock Absorbing Ball Mount #325-GH-12001 is not the right fit for your setup. Since your Tundra's receiver measures 18 inches from the ground and your TAB…
Hi Kristian, great question! The etrailer Anti-Rattle Hitch Collar, part #e55YV, works by taking the slack out between your hitch receiver and the shank of your ball mount or hitch-mounted accessory. It clamps around the outside lip of your 2-1/2…
Hey Scott! The etrailer Anti-Rattle Hitch Collar #e55YV is rated for up to 10,000 lbs gross trailer weight and won't reduce the capacity of a properly matched towing setup. As always, your actual towing capacity is determined by the lowest-rated…
Hey Mike, congratulations on the new truck! You can definitely use the two together. The Curt StowPro 2-Ball Mount #C34FR53HY uses a standard 2-1/2" shank, making it a great match for our etrailer Anti-Rattle Hitch Collar #e55YV. It installs…
Hey Greg! The etrailer Anti-Rattle Hitch Collar for 2.5" Hitch Receivers #e55YV is not compatible with a weight distribution hitch. This is really the only restriction for our anti-rattle. If you need an anti-rattle for a weight distribution…
As you can see in the diagram I provided, the tilt is adjustable up to about 45°. The tilt mechanism has a pin that can be used in two different positions to allow a roughly 15 or 30° degree tilt or the pin can be completely removed for the…
Hey Doug, The Rhino-Rack RS 2500 Roof Rack for Naked Roofs #RRRS566B would be a fit for the roof of your 2017 Ram 2500. That along with the Rhino-Rack T-Loader #RTL002 would allow you to haul your kayaks on the front to clear room for your 5th wheel.…
Hello Jim, Great question, I went to Malone's site and and I do not see that they make one with a 48" roller. The great thing about the Malone Axis Truck Bed and Roof Load Extender with Load Roller #MAL32VR is that it is adjustable, the…
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hey Ryan! The SuperSprings Custom Suspension Stabilizer and Sway-Control Kit #SSA24 will fit your 2023 Ram 3500. It is compatible with SRW and DRW trucks so it doesn't matter either way. It is also compatible on models with and without factory…
Hey David, thanks for reaching out. Yes, we do have a bracket that can be used to mount recovery boards on a roof rack with T-slots. Take a look at the following: - Stow It Recovery Track Holder for Rhino-Rack Pioneer Platform, Reconn-Deck, and…
Haul the long stuff you love—kayaks, canoes, lumber, even a tandem trike—with a truck bed extender in fixed width. This straightforward setup adds a single rear support to span the gap for oversized gear. Compare the extender's height from your hitch to your bed height or wheel wells, especially if you'll run the tailgate down, so everything sits level.
Often no, because the crossbar can be too large for standard roof-mount carriers. If you want side-carry, mount J-cradles on a board spanning the bed and use the extender to support the tail end. Check the crossbar's size and shape against the clamp range of your carrier if you plan to attach anything directly to the extender.
Adjustable tilt can reduce the lift by letting you guide the boat while the bar supports most of the weight. Some use pin positions for smaller or greater tilt, up to about 45°. Expect a learning curve when raising and lowering; control when the bar begins to pivot. If a strap across load stops snags on hull-up loading, removing it can help.
Yes, fixed width extenders work well for long kayaks, canoes, and lumber. The solid crossbar helps keep loads from shifting side to side. Check the extender's weight capacity against your fully outfitted boat. If you plan to switch between bed-level and roof-height support, look for models that can convert between positions with simple adjustments.
It can, but verify the height range first. Some setups end up lower than the bed even at maximum adjustment. Measure from your hitch to the top of the bed (and tailgate if it's down), then compare to the extender's published crossbar height and reach. If you want to rest 4' sheets on the wheel wells, confirm the selected hole height matches your wheel well height and clears the tailgate movement.
Filters
