The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hello Greg, Great question, and yes level towing is important. The average height for a mid-size to full-size travel trailer is 22 to 28 inches, the average height for an F-350 with 4 wheel drive is 20–24 inches, with that being said you will most…
You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…
Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.
...but it is not lightweight aluminum, it is steel, and it does not stow away.
The B&W Tow & Stow 2-Ball Mount - 2" Hitch # BWTS10037C is probably the highest quality one we offer, as these are built extremely well in the USA...
Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
...not in use. The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package # BWRVK3775 you were looking at has four puck style feet that drop into the pucks and a lever on each leg...
Hi Charlie! Installing the EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2" #EH72HR on a 2025 Hyundai Ioniq 5 will require cutting into the bumper fascia to get it installed, but there is no drilling needed. From the center…
Thanks for the picture Richard, I can tell by your picture you have a Model 6 surge actuator on your trailer which the #T4846500183 is the correct replacement for if you were wanting a channel style inner slide member replacement.
If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hello Greg, Great question, and yes level towing is important. The average height for a mid-size to full-size travel trailer is 22 to 28 inches, the average height for an F-350 with 4 wheel drive is 20–24 inches, with that being said you will most…
You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…
Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…
Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.
...but it is not lightweight aluminum, it is steel, and it does not stow away.
The B&W Tow & Stow 2-Ball Mount - 2" Hitch # BWTS10037C is probably the highest quality one we offer, as these are built extremely well in the USA...
Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…
...not in use. The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package # BWRVK3775 you were looking at has four puck style feet that drop into the pucks and a lever on each leg...
Hi Charlie! Installing the EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2" #EH72HR on a 2025 Hyundai Ioniq 5 will require cutting into the bumper fascia to get it installed, but there is no drilling needed. From the center…
Thanks for the picture Richard, I can tell by your picture you have a Model 6 surge actuator on your trailer which the #T4846500183 is the correct replacement for if you were wanting a channel style inner slide member replacement.
If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Adjustable ball mounts offer flexibility and ease for towing enthusiasts. With the ability to adjust height, they ensure a level trailer, enhancing safety and ride comfort. Perfect for those with multiple trailers or varying load heights, these mounts are
Yes, these mounts are built to handle heavy loads, often described as 'beefy' and 'well-built.' They provide a smooth ride even with heavy trailers, making them a reliable choice for serious towing needs.
Yes, they are designed for easy installation and adjustment. Many find them straightforward to set up, allowing for quick changes in height to accommodate different towing needs without hassle.
Absolutely, they help maintain a level trailer, which reduces rocking and swaying. This stability is crucial for a smooth towing experience, especially when dealing with heavy or uneven loads.
An adjustable ball mount allows you to change the height of the hitch, ensuring your trailer is level. This not only improves safety by reducing sway but also enhances ride comfort, making it feel like you're driving a luxury vehicle even with a heavy load.
With adjustable ball mounts, you can easily switch between different trailer heights without needing multiple hitches. This versatility is perfect for those who tow various trailers, from small utility trailers to larger equipment haulers.
Filters
