Hi Thomas! The distance from the center of the hitch pin hole to the center of the ball on the #BW77BR is 13-5/8". This is designed to fit a 2-1/2" receiver with a 10k rating for the 2" and 21k rating for the 2-5/16" ball. What…
It sure will Hans and congrats on the new Outback! The Redarc Tow-Pro Link Bluetooth Brake Controller item #RED57AR is going to work great with your 2026 Subaru Outback Wilderness. Since you have the factory tow package, all you'll need to do is…
Hello Ben, Thanks for writing in! Yes! The WeatherTech Front Auto Floor Mats #WT54TZ you were looking at are made specifically for the factory vinyl floor in your 2026 Ram 2500. For the rear, WeatherTech does not have a matching custom-fit rear mat…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey Andrew. The Redarc Tow-Pro link will indeed work just fine for your 2026 Toyota BZ, and due to it not needing a brake output wire you do not need to hook up the brake out put wire at all. You'll plug the USCAR pig tail #20147 into the Tow-Pro…
Hey Ben, the deciding factor is really where your current jack mounts and whether you want it to stay in that same location. If your enclosed trailer already has a standard A-frame jack opening and you’re happy with the jack staying in the center,…
Hi Tracy, The etrailer Replacement Fabric for etrailer Slide-Out Topper part #e65QV is 96" wide (8ft) and 48" (4ft) deep. It will work with etrailer brand and Solera slide out toppers. The replacement fabric is also packaged with poly cord.…
Good question, Aaron. Since your main detail is the GM MultiPro tailgate, I’d be careful here. The B&W Tow & Stow for 2-1/2" receivers #BWTS20066BMP is specifically listed as compatible with the GM MultiPro tailgate, so if tailgate…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
Thanks for your question Brian. I've included a graphic showing the hole spacing for the mounting bracket on #ARK79FR. Of note, this jack does not include the hardware or a backing plate in order to mount it to your trailer frame. It is meant to…
Hey Noah, so the vertical bike racks like the Thule Revert #TH73VA are so tall they end up putting quite a bit more leverage and torque on the hitch they are installed in. This is why Curt doesn't want you to use them with their hitches like the…
Hello again Jim, Thanks for writing in! You're looking at the correct seal. The GS-1719 DL and TRP markings are the important identifiers, and they match the Double Lip Grease Seal #58846 (or for 2 pack #RG06-050). The additional numbers, such as…
Hitch Pins and Clips with Bent Pin for 2 Inch Hitches
Hook up your bike rack or ball mount with a bent pin that fits a 2 inch hitch for quick, no-fuss security. The bent pin shape is easy to grab and helps avoid fighting with spring securing clips, so your hands stay clear. Solid choice for racks and trailers when you want a simple pin-and-clip setup that goes on and off without drama.
Both secure your setup, but a lock adds theft deterrence. If you want one key for multiple locks, look for a keyed alike option. Some locks can be coded to an ignition key and permanently learn the first key, so they can't be reset after you change vehicles.
It can in some setups. Check that the bent head and clip or lock clear the safety chain loops so the hooks can clip in easily. If space is tight, try flipping the pin orientation or using a slimmer head or longer span to move the clip away from the loops.
Measure the span you need. If your 2 inch receiver tube is recessed, a short span like 2.5 inches may leave too little room to get the clip on. Measure from the outside wall of the hitch to the far side of the pin hole and add space for the clip or lock. If tight, choose an extra-long option.
Free up the tumblers before forcing it. Direct WD-40 into the lock core with the straw, then repeatedly insert and remove the good key to work the lubricant in. Several applications may be needed to get the key to turn and remove the lock.
Standard Hitch Clip
Standard Hitch Pin
Hitch Pins and Clips Parts or Accessories
Filters
